Radikal G30 v.2
Page 7
HEAD ASSEMBLY (FLYBAR HEAD)
No.
Description
Qty
1
2
3
4
5
Part #
6
7
8
9
10
11
12
13
14
15
2
2
2
4
2
2
2
2
2
4
2
2
2
2
M3x5x3 Spacer(
垫圈
)
CNBB0730
M5x10x1 Spacer(
垫圈
)
7x15x5 Thrust Blade Grip Ball Bearing
(
止推轴承
)
M13x16x1 Washer(
平面垫片
)
8x16x5 Bearing(
轴承
)
Metal Main Rotor Blade Grips(
主旋翼夹片
)
M3x5x3 Spacer(
垫圈
)
HI6189
HW6205
CNLR1020
CNLR1014
CNM5X10CS
HW6180A
CNBB715T
HW6182
HW6182
HW6182
CNBB816
HW6205
CNM3x18CS
2
M3 Ball Link(M3
球头螺丝
)
3x7x3 Bearing(
轴承
)
M5x10 Cap Screws(
杯头螺丝
)
M3x18 Cap Screws(
杯头内六角螺丝
)
8x15 Washer(
平面垫片
)
Bell Mixer Arm(
混控臂
)
M3 Ball Link(M3
球头螺丝
)
8x13 Washer(
平面垫片
)
16
17
18
Metal Main Blade Grip Control Arm(
主旋翼夹片摆臂
)
2
CN2510B-1
CN2510B-2
19
HI6181B
2
20
CNLR1003
Washer(
垫片
)3X5X0.5
2
CNM3X8BHCS
M3x8 Button Head Cap Screws(
伞头螺丝
)
2
CNM3X10BHCS
M3x10 Button Head Cap Screws(
伞头螺丝
)
2
Hard Head Dampeners
HW6205 3X5X3
CNLR1020
CNBB0730
CNLR1014
CNM5X10CS
HW6182 8X15X0.5
CNBB715T
HW6180A
M5X10X1
CNBB816
M3X18CS
HW6182
M14X16X1
CNM3X8BHCS
HW6182 8X13X0.5
CNM3X10BHCS
19
18
6
7
8
9
10
11
3
4
5
2
1
16
15
12
13
14
17
BELL MIXER RATIOS
BAG 1
Drop some Medium threadlock into the side of
the blade grip. Place the grip arm over the grip
and install the M3 button head screws as shown
with washer. Slide the M3x18 button head screw
through the bell mixer arm from the flat side, add
one M3x5x3 spacer and apply a drop of Medidum
threadlock to the end of the threads before in-
stalling into the blade grip. Tighten the bolt
until there is no end to end movement,
but do not overtighten the bolt as you
can strip out the hole or bind
the bearings. Make two
assemblies.
BELL MIXER RATIOS
1:1.6
1:1.3
There are two types of dampeners provided. The hard black plastic dampeners
(HI6520A) should only be used for hard 3D flying. If using the hard plastic dampeners,
use only one of the (HW6182) 8x13 spacer. Press in the head dampers into the rotor
head block. Lubricate the inside surface of each damper with light oil. Press one M8x16
ball bearing into both ends of each main rotor blade grip. Slide
one M14 thrust washer against the bearing closest to the
main rotor blade. Make sure that the bearing and
the thrust washer are properly seated into the
deep end of the blade grip. If necessary use
a socket that matches the outside
diameter of the bearing and
press into position. Make
two assemblies.
Press one M3x7 flanged ball bearing into one
side followed by one M3x5 spacer and another
flanged bearing from the opposite side. If the bear-
ing is tight, lightly sand the bell mixer and use Red
threadlock to bond the bearing in place. Install the
CNLR1014 short steel ball into the single hole side of
the bell mixer and install the CNLR1020 medium steel
ball using Blue threadlock. Install the medium steel ball ac-
cording to the table to suit your flying preference. Make two
assemblies.
20
21
21
HW6180BS
Feathering Shaft
1
SIDE PROFILE - BLADE GRIP
RECESSED CREVICE FACES MAIN SHAFT
THRUST BEARING INSTALLATION GUIDE
GROOVES INSIDE
SMALLER ID
LARGER INNER DIAMETER TOWARDS HEAD BLOCK
LARGER ID
17
2
HI6520A
Hard Plastic Dampeners
These bearings are already
pressed into the blade grips.
