Century Helicopter Products Hummingbird Elite 3D Pro Скачать руководство пользователя

Страница: 8 / 12

Combining Major Assemblies (10-1, 10-2)

42) Install the

Brass Washer

from bag CNE313 onto the

Main Shaft

located in the

Upper Frame Assembly

. Align the

Main Shaft

with the

opening on the ﬂanged portion of the

Bearing

in the

Lower Frame

Assembly.

43) Align the bolt holes in the

Tail Boom Brace Bracket

with the

Rear

Lower Bracket

and attach them using the two

M2x5 Machine Screws

Section 10: Combining Major Assemblies

Bags Used:

CNE313, CNE301

Rotor Head Linkage (11-1, 11-2)

There are 3 different sets of links in CNE307.

Short Double Links

Long Adjustable Links

Long Solid Links

44) Snap on the

Short Double Links

to the

Control Balls

on the

Main Blade Grips

and to the

Inner Control

Balls

of the

Swing Arm

45) Snap on

Long Adjustable Links

to the

Outer Control

Balls

of the

Swing Arms

and to the

Control Balls

the inner race of

Swashplate

46) Insert the

Long Solid Links

through the

Plastic Link

Stabilizer

and attach to the

Inner Control Balls

of the

Outer Seesaw Assembly

and to the

Control Balls

the

Swashplate

inner race.

Section 11: Rotor Head Linkage

Bags Used:

CNE307

Short Double

Link #CNE307

Long Adjustable

Link #CNE307

Long Solid Link

#CNE307

(1 on each side)

Swing Arm

#CNE306

Brass Washer

#CNE313

Upper Frame

Assembly

M2x5 Machine

Screw #CNE310 (2)

M3x18 Machine

Screws #CNE301 (2)

43) Mount the

Motor

using the

Motor Mount Spacers

and

M3x18

Machine Screws

provided in CNE301. Align so that the

Pinion Gear

of the

Motor

meshes smoothly with the large

Autorotation Hub & Gear

If using any motor other than

CNE252 Lightning Brushless Motor

other third-party motor mounting hardware may be needed.

Rear Lower

Bracket

#CNE310

Lower Frame

Assembly

Tail Boom Brace

Bracket #CNE310

Bearing

#CNE213F

Main Shaft

#CNE313

Century Lightning Brushless

Motor #CNE252

Pinion Gear 10-Teeth

#CNE056G

Pinion Gear 11-Teeth

#CNE056GB

Autorotation

Hub & Gear

#CNE250

Motor Mount

Spacer

#CNE301

Short Double

Link #CNE307

Long Adjustable

Link #CNE307

Short Double

Link #CNE307

Long Adjustable

Link #CNE307

Main Blade Grips

#CNE302

Outer

Control

Ball

Inner

Control

Ball

Control Ball

Swashplate

(inner race)

#CNE314

Outer Seesaw

Assembly

#CNE306

Control Ball

(1 on each side)

10-1

10-2

11-1

11-2

Содержание Hummingbird Elite 3D Pro













Результаты поиска

Содержание Hummingbird Elite 3D Pro

Отзывы:

Похожие инструкции для Hummingbird Elite 3D Pro

Бренды по названию

Популярные бренды

Century Helicopter Products Hummingbird Elite 3D Pro, Сборка и инструкция по эксплуатации

Результаты поиска

Содержание Hummingbird Elite 3D Pro

Отзывы:

Похожие инструкции для Hummingbird Elite 3D Pro

Бренды по названию

Популярные бренды