Century Helicopter Products Hummingbird Elite 3D Pro Скачать руководство пользователя

Страница: 5 / 12

Landing Struts

(Plastic)

#CNE326

Section 6: Main Rotor Hub

Bags Used:

CNE303, CNE313

Main Rotor Head Assembly (6-1, 6-2)

Get parts bag CNE303

CNC Rotor Hub

and rotor hub collar and Part bag

CNE313

Main Shaft

, spacers and main shaft collar.

Place not used here in a container to avoid losing them.

19) Insert CNE313

Main Shaft

into the

CNC Rotor Hub

. Take note that the

Main Shaft

has three holes. Mount the

CNC Rotor Hub

onto the end

of the

Main Shaft

where the hole is closest to the tip of the

Main Shaft

(least material between the hole in the shaft and the end of the shaft).

Put the

Plastic Link Stabilizer

over the bottom of the

CNC Rotor Hub

Note, that there is a hole in the middle base of the

CNC Rotor Hub

. Align

the holes from the

Plastic Link Stabilizer

to the

CNC Rotor Hub

, hold it up to

a lamp, you should be able to see light through the hole (if the lamp is

20) Insert the 11mm

Jesus Pin

through the assembly. Tap or press the

Jesus Pin

in place using hobby pliers.

Seesaw & Rotor Hub Collar (7-1, 7-2, 7-3)

Open parts bag CNE306 seesaw assembly.

21) Place the

Center Pivot Joiner

inside the

CNC Rotor Hub

(long ends of the

Center Pivot Joiner

will protrude from the large slots of the

CNC Rotor Hub

Short ends will protrude from the small slots).

22) Remove the

Head Button

from on top of the

CNC Rotor Hub

and insert the

Inner Seesaw Assembly

and align it with the

Center Pivot Joiner

. Attach

the

Inner Seesaw Assembly

to the

Center Pivot Joiner

using the supplied

M2x7 Countersunk Screws

from bag CNE306. Once completed, replace

the

Head Button

onto the

CNC Rotor Hub

23) Attach the

Swing Arms

using the supplied

M2x7 Button Head Screws

to the

Inner Seesaw Assembly

with the two

control balls

facing the

Inner Seesaw

Assembly

(7-3).

24) Start the supplied

M2x5 Machine Screw

into the

Rotor Hub Collar

and

insert it over the

CNC Rotor Hub

until it is ﬂush with the

Plastic Link

Stabilizer

. Apply locktite to screw and tighten.

Place extra small parts in a container.

Section 7: Seesaw & Rotor Hub Collar

Bags Used:

CNE306, CNE313

Main Shaft

#CNE313

Plastic Link Stabilizer

#CNE303

CNC Rotor Hub

#CNE303

Jesus Pin

(goes here)

#CNE303

Center Pivot Joiner

#CNE306

Inner Seesaw

Assembly #CNE306

Rotor Hub

Collar

#CNE303

Center Pivot Joiner

#CNE306

M2x7 Countersunk

Screw (2) #CNE306

6-1

6-2

7-1

7-2

7-3

Head Button

#CNE303

CNC Rotor Hub

#CNE303

Swing Arm

#CNE306

M2x5 Machine

Screw

#CNE303

Swing Arm

#CNE306

M2x7 Button

Head Screw

#CNE306

Control Ball

LOCK

TITE

Plastic Link

Stabilizer

#CNE303

Содержание Hummingbird Elite 3D Pro













Результаты поиска

Содержание Hummingbird Elite 3D Pro

Отзывы:

Похожие инструкции для Hummingbird Elite 3D Pro

Бренды по названию

Популярные бренды

Century Helicopter Products Hummingbird Elite 3D Pro, Сборка и инструкция по эксплуатации

Результаты поиска

Содержание Hummingbird Elite 3D Pro

Отзывы:

Похожие инструкции для Hummingbird Elite 3D Pro

Бренды по названию

Популярные бренды