Central Pneumatic 91044 Скачать руководство пользователя

Страница: 6 / 12

Page 6

SKU 91044

For technical questions, please call 1-800-444-3353.

Warning! Disconnect the Nailer from the air compressor whenever load-

ing or servicing.

ALWAYS WEAR ANSI APPROVED IMPACT SAFETY GOGGLES WHEN RE-

LOADING OR DOING ANY OTHER MAINTENANCE ON THIS TOOL.

Other people in the work area must also wear ANSI approved impact
safety goggles.

Loading Nails

See

FIGURE 2

on page 7.

Slide the Tab (70) back and the Latch (83) will hold it in place.

Load a stick of nails into the top slot, making sure the nail heads are facing up.

Be Careful

. When you pull back on the Latch (83) to release the Tab (70), it will spring

forward with force. Keep your fingers clear when you release the Latch (83) and slide
the Tab (70) forward.

Note:

The Nailer may not work if there are only two or three nails left in the tool. If there are
only a few nails remaining, simply load another strip of nails into the Magazine behind
the few remaining nails and the Nailer will be ready for further use.

Operation

Testing the Full Sequential Safety Trip Mechanism

Warning: Even though the nailer should be empty during this procedure,

ALWAYS point the nailer at a piece of scrap wood when testing.

Make sure the tool is disconnected from the power supply.

Completely empty the Magazine (76) of nails.

The Nailer should not fire if the Safety (41) is not depressed against the workpiece.

Make sure the Trigger (47) and Safety (41) move freely, without sticking.

Connect the air supply to the tool at the Air Inlet (90). Set the regulator at the recom-
mended

70 to 125 PSI

Test the tool by depressing the Safety (41) against the workpiece without pulling the
Trigger (47).

The Tool must not cycle (fire).

If it cycles (fires), stop immediately and

have it repaired by a qualified service technician.

Hold the tool away or off of the workpiece. The Safety (41) of the tool should return to
its original position. Squeeze the Trigger (47).

The tool should not cycle (fire).

If the

tool fires, stop immediately and have it repaired by a qualified service technician.

Depress the Safety (41) against the workpiece and squeeze the Trigger (47).

The tool

must cycle (fire) only once.

Release the Trigger and squeeze it again.

The tool

must not cycle (fire).

With the Trigger held, carefully lift the nailer and press it against

the workpiece again.

The tool must not cycle (fire).

If it fails to perform in the manner

explained in bold, have it repaired by a qualified service technician.

REV 06/05

Rev 11/06

Содержание 91044













Результаты поиска

Содержание 91044

Отзывы:

Похожие инструкции для 91044

Бренды по названию

Популярные бренды

Central Pneumatic 91044, Руководство по сборке и эксплуатации

Результаты поиска

Содержание 91044

Отзывы:

Похожие инструкции для 91044

Бренды по названию

Популярные бренды