Central Pneumatic 91044 Скачать руководство пользователя

Страница: 10 / 12

Page 10

SKU 91044

For technical questions, please call 1-800-444-3353.

Maintenance

Disconnect the Nailer from the air source hose before attempting any maintenance

Wipe tool clean with a lint free cloth and inspect it for damage. Do not use the tool if
you find damage. Have it repaired by an authorized service technician.

Always test the Full Sequential Safety mechanism before each use (see page 6).

Keep all screws tight. Loose screws may damage the tool and cause personal injury.

Make sure that Base (29) is clear of all dirt or debris.

Solution

Verify screws are tight,
Check/replace O-rings or seals

Use a compressor that delivers

the proper CFM,

Add air tool oil (not incl.),
Check/replace O-rings or seals

Verify screws are tight,
Check/replace O-rings, seals.

Verify fastener size,
Replace fasteners,
Tighten screws,
Clean Magazine,
Inspect Driver Unit

Symptom

Top of tool or Trigger

(47) leaks air

Sluggish operation, or

will not operate

Bottom of tool leaks air

Frequent Jamming

Cause

Loose Screws,
Worn or damaged O-rings or seals

Inadequate air supply,

Inadequate lubrication,
Worn/damaged O-rings or seals

Loose Screws,
Worn/damaged O-rings, seals.

Incorrect fasteners,
Damaged fasteners,
Magazine (76) or Nose screw loose,
Dirt inside Magazine,
Worn or damaged Driver Unit

Note:

Contact Harbor Freight Tools for repair/replacement parts.

Troubleshooting

Any internal repair should be performed by an authorized service technician.

Содержание 91044













Результаты поиска

Содержание 91044

Отзывы:

Похожие инструкции для 91044

Бренды по названию

Популярные бренды

Central Pneumatic 91044, Руководство по сборке и эксплуатации

Результаты поиска

Содержание 91044

Отзывы:

Похожие инструкции для 91044

Бренды по названию

Популярные бренды