background image

Page 11

For technical questions, please call 1-888-866-5797.

Item 67536 
        

NOTICE

FOR CEMENT AND MORTAR ONLY. 

Do not use with Epoxy 2-part resin mix.

materials are dumped while the Drum is 
rotating.

8. 

When finished, flip the Switch to the 
“OFF” (O) position and disconnect the 
power cord.

9. 

Tilt the Drum angle as far down as 
possible to drain all fluids from Drum.

10.  Clean, then store indoors and out of 

children’s reach.

MAINTENANCE AND SERVICING

  Procedures not specifically 

explained in this manual must 
be performed only by a qualified 
technician.

 

TO PREVENT 
SERIOUS INJURY 

FROM ACCIDENTAL OPERATION: 
Turn the Power Switch of the tool to its 
“OFF” position and unplug the tool from 

its electrical outlet before performing any 
inspection, maintenance, or cleaning 
procedures.

TO PREVENT SERIOUS INJURY 
FROM TOOL FAILURE: 
Do not use damaged equipment.  
If abnormal noise or vibration 
occurs, have the problem 
corrected before further use.

Cleaning, Maintenance, and Lubrication

1. 

BEFORE EACH USE,

 inspect the 

general condition of the tool.  Check for 
loose hardware, misalignment or binding 
of moving parts, cracked or broken parts, 
damaged electrical wiring, damaged or 
cracked belts, and any other condition 
that may affect its safe operation.

2. 

AFTER USE,

 immediately wash out all 

debris from the inside and outside of the 
Cement Mixer. Scrub the inside of the 
Drum with a stiff, long handled bristle 

brush for best results. Wipe external 
surfaces of the tool with clean cloth.

3. 

DO NOT apply water in or around the 
Motor Base Cover

4. 

PERIODICALLY 

recheck all fasteners 

and other connections for tightness.

5. 

WARNING!  If the supply cord of 

this power tool is damaged, it must be 
replaced only by a qualified service 
technician.

Belt Inspection and Tensioning

1. 

Retighten belt after the first 25 hours of 
use. To test the tension, follow the steps 
below.

2. 

Remove belt cover.

3. 

Examine belt for cracks, tears in the 
backing, or other damage.  Replace belt 
if damaged according to steps below:

a. Loosen the motor bracket bolts and 

slide the bracket up as far as possible.

b. Slide the old belt off of the larger pulley 

first, then remove it from the motor 
pulley.

c. Put the new belt around the small pulley 

first, then around the large pulley.

Содержание 67536

















Отзывы: