Page 8
For technical questions, please call 1-888-866-5797.
Item 43389
S
AFET
y
Op
ERA
TION
M
AINTENAN
c
E
S
ETU
p
12. Install
V-belts
(A4 and A17).
a. Turn the Belt Tension Handle (3) and
move the pulleys closer together.
b. Place the Center Pulley (A15) on the
Pivot Idler (A14), and into the Pulley Guard
center hole (See the Pulley Assembly
Drawing at the end of this manual).
c. Place the longer V-belt (A4) between
Spindle Pulley (A6) and the Center Pulley.
d. Refer to the chart inside the Pulley Guard
lid to select speed and belt locations.
e. Place V-belt (A17) between the
Motor Pulley and the Center Pulley.
f. Turn the Belt Tension Handle to tighten the
belts (moderately), and hold in place.
g. Turn the Motor Adjusting Knob (1)
clockwise to lock the belt tension.
Note:
To test the proper belt tension,
push in on the center of each belt at its center.
It should move only 1/2" (in or out).
NOTIcE:
Overtightening the belts can
cause the motor to bind, and not start. It
can also damage Motor bearings.
13. Attach Knob (A12) to the Pulley
Guard using Screw (A13).
WARNING!
Do not plug power cord in yet.
14. Attach
Motor cord
(41) to the Motor connector box.
a. Open Motor connector box
located under the motor.
b. Remove green (ground) screw and
connect the green wire round terminal
to the screw and retighten.
c. Insert terminal end of the white wire
to spade terminal #4. Seat firmly.
d. Insert terminal end of the black wire
to spade terminal #1. Seat firmly.
e. Set the cord strain relief in the center groove.
f. Close Motor connector box.
15. Mount the 3 Rods (10) to the Head
Assembly Hub (7). Thread a Knob
(9) onto the tip of each Rod.
16. Install the
chuck
(C8).
a. Thoroughly clean the tapered hole in
the Chuck and the Arbor (C9) of all dirt,
grease, oil, and protective coatings.
b. Place a piece of scrap wood on the
Table to protect the Chuck nose.
c. Slide the Chuck onto the Arbor.
d. Loosen the Column Clamp (B16) and turn
the Table Crank (B4) to raise the Table so
that it is about two inches from the Chuck.
e. Turn the Chuck sleeve clockwise
and open the jaws completely.
f. Turn the Feed Handle counterclockwise
and force the Chuck against the
scrap wood until it is secure.
17. Verify that the Table is square (90º) to
the Head Assembly and drill bit.
a. Secure a three inches drill bit in the Chuck.
b. Raise the Table to within four
inches of the Chuck.
c. Place the long side of a combination
square on the Table.
d. Align the short side of the square to the drill bit.
e. If the Table is not square to the bit, loosen
Set Screw (B1) with the Hex Key and the
Machine Screw (B8) with the Wrench (B20).
f. Rotate the Table until it is square to the bit.
g. Retighten the Machine Screw,
then the Set Screw.
Set Screw (B1)
Machine
Screw (B8)
18. Mounting the Oiler.
a. Use the 4 Screws (51) to attach the
2 Brackets (50) to the tapped holes in
the left side of the head casting.
b. Carefully thread the Spigot Assembly
(53) onto the Oil Bottle (52), then snap
the bottle into the Brackets (50).
c. Making sure that the brass spigot valve
is closed first, remove the bottle cap
and add your lubricant of choice.