Central Machinery 38470 Скачать руководство пользователя страница 15

Страница: 15 / 24

Page 15

For technical questions, please call 1-888-866-5797.

Item 38470

The Letter “G”

Two blanks are required for this letter:

•

14″ long

•

3″ long

3-3/4″

1″

1st Bend

2nd

3rd

4th

1″

1st Bend

1″

Using chalk, mark off 3-3/4″ in from each side of the long blank. Mark off one inch on each side as shown above.

2. Set the Right Angle Bend Attachment into place.

3. Set the stock in the Bender so that the Right Angle Bend Attachment will bend at the first chalk mark. Bend to 45°.

4. Make a bend at your second chalk mark to 45°.

5. Take the stock out of the Bender. Insert the second side. Repeat steps 3 and 4.

Mark off 1″ on the 3″ blank.

7. Set the blank into the Bender at the chalk mark. Bend to 90°.

Weld the 1″ side of the 3″ piece to the bottom portion of the “G” . The longer
side of the 3″ blank will form the inside part of the G.

The Letter “H”

Three blanks are required for this letter:

•

6″

•

6″

•

3-3/4″

Weld the 3-3/4″ blank to the center of each 6″ blank.

Make certain that both 6″ blanks are even with each other.

The Letter “I”

Three blanks are required for this letter:

•

5″

•

5″

•

5-5/8″

Weld the 5-5/8″ blank to the center of each 5″ blank.

Make certain that both 5″ blanks are equally opposite each other.

The Letter “J”

One blank is required for this letter:

•

11″

3-1/4″

1-1/4″

1st Bend

2nd

3rd

1-1/4″

Using chalk, mark off 1-1/4″ from one side. From this mark, mark off 3-1/4″.
From the second mark, mark off another 1-1/4″.

2. Set the Right Angle Bend Attachment into place.

3. Set the stock in the Bender so that the Right Angle Bend Attachment will bend at the first chalk mark. Bend to 45°.

4. Move the blank to the second chalk mark. Bend to 45 degrees.

5. Move the blank to the third chalk mark and bend to 20 degrees.

Содержание 38470

























Результаты поиска

Содержание 38470

Отзывы:

Бренды по названию

Популярные бренды

Central Machinery 38470, Руководство пользователя и инструкции по безопасности

Результаты поиска

Содержание 38470

Отзывы:

Бренды по названию

Популярные бренды