manualshive.com logo in svg

Central Machinery 38470, Руководство пользователя и инструкции по безопасности

Поделиться
Скачать
Central Machinery 38470 Скачать руководство пользователя страница 13

Page 13

For technical questions, please call 1-888-866-5797.

Item 38470 
        

The Letter “B”

Three blanks are required for this letter:

• 

8-7/8″ long

• 

8-7/8″ long

• 

6″ long

1st Bend

2nd

3rd 4th

2-3/4″

2-3/4″

1″

1″

1. 

Using chalk mark off 2-3/4″ in from each side.  Mark off one inch from the first 
chalk mark on each side.  Do the same for the second 8-7/8″ blank.

2.  Set the Right Angle Bend Attachment into place.

3.  Set the stock in the Bender so that the Right Angle Bend Attachment 

will bend at the first chalk mark.  Bend to 45 degrees. 

4.  Move the stock to the second chalk mark and bend to 45°.

5.  Pull the stock out of the bender and insert the stock with the opposite 

end in the bender.  Make the 3rd bend at 45 degrees.  

6.  Slide the stock to the fourth position and bend to 45°.

7. 

Weld the completed two 8-7/8″ pieces together, these will be the curves in the 
letter “B”.  Weld on the 6″ piece to form the spine of the letter.

The Letter “C”

One blank is required for this letter:

• 

14″ long

1st Bend

2nd

3rd

4th

3-3/4″

3-3/4″

1-1/4″

1-1/4″

1. 

Using chalk, mark off 3-3/4″ in from each side.  

2. 

From the inside mark, measure in another 1-1/4″ and mark it off from each side.

3.  Set the Right Angle Bend Attachment into place.

4.  Set the stock in the Bender so that the Right Angle Bend Attachment will bend at the first chalk mark.  Bend to 45°.

5.  Make a bend at your second chalk mark to 45°.

6.  Take the stock out of the Bender.  Insert the second side.  Repeat steps 3 and 4.

Содержание 38470

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды