18
At the end of the operation the pump will stop, the LED will remain a
STEADY LIGHT
(2 minutes)
and the speaker will emit a
COUNTINUOUS BUZZER
sound (30 seconds). This confirms the pump
received a signal from the cutting head acknowledging that the blades are
completely closed; the display will show the following flashing screen
(Ref. to
section 7.5
for further details).
Release the finger from the pump button (2) to initiate the SMART RELEASE function of the pump;
the operator should then check to ensure the blades are fully retracted to the start position.
Remove the battery from the pump.
Disconnect the flexible hose from the pump and cutting head.
At the end of the operation, in the event of a flashing LED light (2 minutes) and an
intermittent buzzer (30 seconds), this is to inform the operator that the wireless signal
to indicate the blades have fully traveled has not been received.
The display will show the following flashing screen
(Ref. to
section 7.6
for further
details).
STEP 2 – Bringing the cutting head down into the manhole
Secure the pump in proximity of the manhole or to the ladder, using the shoulder strap sup-
plied
(Ref. to Fig. 4).
The maximum distance between the cutting head and the pump is 33 ft
(10 m) assuming that the pump is positioned in proximity of the manhole or on the ladder
under the street level.
Do not place the pump on dirty surfaces or in the presence of water
.
Lower the cutting head and the flexible hose into the manhole.
Position the blades of the cutting head perpendicularly around the cable that has been identi-
fied for the cut, as described in
section 4.3.
Stabilize the cutting head position and support the head by strapping it to the above wires or
cable holders. It is possible to hook the cutting head with the SS-TCY strap hooked to the hang-
ing points of the head (Ref. to Fig. 11).
Connect one end of the grounding wire to the cutting head and the other end to the relevant
grounding attachment (Ref. to
section 4.2
).
Connect the flexible hose to the cutting head (Ref. to Fig. 7),
the operator should now leave the manhole
.
After all personnel have exited the manhole or cable space, con-
nect the flexible hose to the pump (Ref. to Fig. 7).
Insert the battery.
Wake up the pump by pressing forward the control button (11)
(display ON)
.
P
p
= 325 bar
RESET
SW:S1J41405
LED
OFF
ERROR
001
30001
BATTERY
P
n
= 729 bar
002
003
BATTERY
004
LED
ON
LED
OFF
LED
ON
max.
BATTERY
BATTERY
min.
B68RC
NR 17AW125
10
29990
BATTERY
max 90°
90°
OK
P
n
= 729 bar
P
p
= 731 bar
RC ON
RESET
SW:S1J76202
P
n
= 729 bar
P
= 0 bar
P = 0 bar
P
n
= 10573 psi
LED
ON
LED
OFF
max 90°
60°
*
1
*
2
3
4
5
*
6
*
7
*
8
*
9
10
P
= 0 psi
P = 0 bar
P
n
= 729 bar
P
= 0 bar
BEEP
BEEP
RC OFF
P
n
= 729 bar
OK
OK
SAVE 60
%
100
P = 0 psi
P = .... bar
P
n
= 729 bar
OK
P
n
= 729 bar
P
p
= 731 bar
P
n
= 729 bar
P
= 0 bar
58
01
59
60
.........
P
p
= 325 bar
RESET
SW:S1J41405
LED
OFF
ERROR
001
30001
BATTERY
P
n
= 729 bar
002
003
BATTERY
004
LED
ON
LED
OFF
LED
ON
max.
BATTERY
BATTERY
min.
B68RC
NR 17AW125
10
29990
BATTERY
max 90°
90°
OK
P
n
= 729 bar
P
p
= 731 bar
RC ON
RESET
SW:S1J76202
P
n
= 729 bar
P
= 0 bar
P = 0 bar
P
n
= 10573 psi
LED
ON
LED
OFF
max 90°
60°
*
1
*
2
3
4
5
*
6
*
7
*
8
*
9
10
P
= 0 psi
P = 0 bar
P
n
= 729 bar
P
= 0 bar
BEEP
BEEP
RC OFF
P
n
= 729 bar
OK
OK
SAVE 60
%
100
P = 0 psi
P = .... bar
P
n
= 729 bar
OK
P
n
= 729 bar
P
p
= 731 bar
P
n
= 729 bar
P
= 0 bar
58
01
59
60
.........
11
Содержание B68M-P18A-KV-RC2
Страница 2: ...2 FIG 2 A G F C B FIG 1 1 5 9 10 12 8 7 3 2 4 2 11 D 6 E ...
Страница 31: ...31 ...
