Cedar Summit Sedona F25035 Скачать руководство пользователя страница 23

Страница: 23 / 95

[email protected]

Step 3: Swing Wall Prep

Part 3

It is important to assemble the frame on a flat, smooth surface.

Attach (2630) SW Top to (2757) LT Post Assembly and (2758) RT Post Assembly with 2 (WB1) 5/16 x 1”

Wafer Bolts (with flat washer) connecting to previously installed t-nuts. (fig. 3.5 and 3.6)

Attach (2768) Panel Floor to (2757) LT Post Assembly and (2758) RT Post Assembly with 2 (H9) 1/4 x 1-1/4”

Hex Bolts (with lock washer and flat washer) connecting to previously installed t-nuts. (fig. 3.5).

Place 1 (2824) Diagonal Support to each side of (2769) Panel BT Frame, notice the hole locations and attach

with 1 (H10) 1/4 x 2-1/4” Hex Bolt (with lock washer and flat washer) per board connecting to previously installed

t-nuts. (fig. 3.5 and 3.7).

Place (8587) Diagonal under (2824) Diagonal Support and loosely attach with 1 (H10) 1/4 x 2-1/4” Hex Bolts

(with lock washer, flat washer and t-nut). (fig. 3.5 and 3.7).

Wood Parts

Hardware

2824

Fig. 3.6

Note which bolt holes are used

WB1

8587

WB1

2758

8587

2824

Fig. 3.7

FW2

H10

8587

2768

2630

2757

2769

2824

Fig. 3.5

FW1

LW1

2 x

5/16 x 1” Wafer Bolt (5/16” flat washer)

2 x

1/4 x 1-1/4” Hex Bolt (1/4” lock washer, 1/4” flat washer)

3 x

1/4 x 2-1/4” Hex Bolt (1/4” lock washer, 1/4” flat washer and 1 1/4” t-nut)

2 x

Diagonal Support 5/4 x 4 x 24-1/2”

1 x

Diagonal 2 x 3 x 42-1/4”

TN1

LW1

FW1

H10

Содержание Sedona F25035
































































































Результаты поиска

Содержание Sedona F25035

Отзывы:

Бренды по названию

Популярные бренды

Cedar Summit Sedona F25035, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Sedona F25035

Отзывы:

Бренды по названию

Популярные бренды