background image

www.usaprocom.com

7

200015-01B

AIR FOR COMBUSTION AND VENTILATION

 WARNING: This heater shall 

not be installed in a confined space 

or unusually tight construction 

unless provisions are provided 

for  adequate  combustion  and 

ventilation air. Read the following 

instructions to insure proper fresh 

air for this and other fuel-burning 

appliances in your home.

Today’s homes are built more energy efficient 

than ever. New materials, increased insulation 

and new construction methods help reduce 

heat loss in homes. Home owners weather 

strip  and  caulk  around  windows  and  doors 

to keep the cold air out and the warm air in. 

During heating months, home owners want 

their homes as airtight as possible.

While it is good to make your home energy 

efficient, your home needs to breathe. Fresh 

air must enter your home. All fuel-burning ap-

pliances need fresh air for proper combustion 

and ventilation.

Exhaust fans, fireplaces, clothes dryers and 

fuel burning appliances draw air from the house 

to operate. You must provide adequate fresh 

air for these appliances. This will insure proper 

venting of vented fuel-burning appliances.

PROVIDING ADEQUATE VENTILATION

The following are excerpts from 

National Fuel 

Gas Code, ANSI Z223.1/NFPA 54, Air for 

Combustion and Ventilation.

All spaces in homes fall into one of the three 

following ventilation classifications:

1.  Unusually Tight Construction

2.  Unconfined Space

3.  Confined Space

The information on pages 7 through 9 will help 

you classify your space and provide adequate 

ventilation.

Unusually Tight Construction

The air that leaks around doors and windows 

may provide enough fresh air for combustion 

and ventilation. However, in buildings of un-

usually tight construction, you must provide 

additional fresh air.
Unusually  tight  construction  is  defined  as 

construction where:

a.  walls and ceilings exposed to the outside 

atmosphere  have  a  continuous  water 

vapor retarder with a rating of one perm 

(6 x 10

-11

 kg per pa-sec-m

2

) or less with 

openings gasketed or sealed and

b.  weather  stripping  has  been  added  on 

openable windows and doors and

c.  caulking or sealants are applied to areas 

such as joints around window and door 

frames, between sole plates and floors, 

between wall-ceiling joints, between wall 

panels, at penetrations for plumbing, elec-

trical and gas lines and at other openings.

If your home meets all of these three criteria, 

you  must  provide  additional  fresh  air.  See 

Ventilation Air From Outdoors

, page 9.

If your home does not meet all of the three 

criteria above, proceed to 

Determining Fresh-

Air Flow For Heater Location

, page 8.

Confined and Unconfined Space

The National Fuel Gas Code, ANSI Z223.1/

NFPA 54

 defines a confined space as a space 

whose volume is less than 50 cubic feet per 

1,000 Btu/hr (4.8 m

3

 per kw) of the aggregate 

input rating of all appliances installed in that 

space and an unconfined space as a space 

whose volume is not less than 50 cubic feet per 

1,000 Btu/hr (4.8 m

3

 per kw) of the aggregate 

input rating of all appliances installed in that 

space. Rooms communicating directly with the 

space in which the appliances are installed*, 

through openings not furnished with doors, are 

considered a part of the unconfined space.
* Adjoining rooms are communicating only if 

there are doorless passageways or ventilation 

grills between them.

Содержание CRHEB24RT





































Отзывы: