background image

www.usaprocom.com

200015-01B

4

  WARNING:  The log set  be-

comes very hot when running. 

Keep children and adults away 

from hot surfaces to avoid burns 

or clothing ignition. Fireplace 

will remain hot for a time after 

shutdown. Allow surfaces to 

cool before touching.

 WARNING: Carefully super-

vise young children when they 

are in the room with the heater.

 WARNING: You must operate 

this log set with screen in place.

1.  Do not place Propane/LP supply tank(s) 

inside any structure. Propane/LP supply 

tank(s) must be placed outdoors.

2.  This  heater  shall  not  be  installed  in  a 

bedroom or bathroom.

3.  This heater needs fresh air ventilation to 

run properly. This heater has an Oxygen 

Depletion Sensing (ODS) safety shutoff 

system. The ODS shuts down the heater 

if not enough fresh air is available. See 

Air 

for Combustion and Ventilation

, pages 7 

through 9. If heater keeps shutting off, see 

Troubleshooting

, page 29.

4.  Keep all air openings in front and bottom 

of heater clear and free of debris. This will 

ensure enough air for proper combustion.

5.  If heater shuts off, do not relight until you 

have provided fresh, outside air. If heater 

keeps shutting off, have it serviced.

6.  Do not run heater:

• Where flammable liquids or vapors are 

used or stored.

• Under dusty conditions.

7.  Before using furniture polish, wax, carpet 

cleaner, or similar products, turn heater 

off. If heated, the vapors from these prod-

ucts may create a white powder residue 

within burner box or on adjacent walls or 

furniture.

SAFETY

8.  Do not use heater if any part has been 

under water. Immediately call a qualified 

service  technician  to  inspect  the  room 

heater  and  to  replace  any  part  of  the 

control system and any gas control which 

has been under water.

9.  Turn off heater and let cool before servic-

ing. Only a qualified service person should 

service and repair heater.

10. Operating  heater  above  elevations  of 

4,500 feet could cause pilot outage.

11. To  prevent  performance  problems,  do 

not use propane/LP fuel tank of less than 

100 lbs. capacity.

12. Do not use this heater as a wood-burning 

heater. Use only the logs provided with the 

heater.

13. Solid  fuels  should  not  be  burned  in 

fireplace  in  which  a  vent-free  log  set  is 

installed. Do not use this heater to cook 

food or burn paper or other objects.

14. To prevent sooting, follow the instructions 

in 

Care and Maintenance

 (see page 27).

15. Do not add extra logs or ornaments such 

as pine cones, vermiculite, or rock wool. 

Using these added items can cause soot-

ing. Do not add lava rock around base. 

Rock and debris could fall into the control 

area  of  heater. After  servicing,  always 

replace screen before operating heater.

16. This heater is designed to be smokeless. If 

logs ever appear to smoke, turn off heater 

and call a qualified service person.

 

Note: During initial operation, slight smok-

ing could occur due to log curing and the 

heater burning manufacturing residues.

17. If fireplace has glass doors, never operate 

this heater with glass doors closed. If you 

operate heater with doors closed, heat will 

build up inside fireplace and cause glass 

to  burst.  If  fireplace  opening  has  vents 

at the bottom, you must open the vents 

before operating log set. Always operate 

heater with glass doors fully open.

18. Do not use this heater if any log is broken. 

Do not operate heater if a log is chipped 

(dime-size or larger).

Содержание CRHEB24RT





































Отзывы: