manualshive.com logo in svg

Cebora PLASMA PROF 164 HQC, Руководство по обслуживанию

Поделиться
Скачать
Cebora PLASMA PROF 164 HQC Скачать руководство пользователя страница 28

CEBORA S.p.A.

 

28 

Correct? 

 
 YES 
 
 NO 

♦

 

Check the wiring between J3 settings board (54) and J7 of control board (38). 

♦

 

With Power Source off, temporarily disconnect J7 from control board (38) and 
check the resistance on terminals 3 and 7 of settings board (54). Correct value = 
>Mohm. If short-circuited or low-resistance, replace the settings board (54). 

♦

 

Replace control board (38). 

 

POWER SOURCE OUTPUT CURRENT TRANSDUCER POWER SUPPLY TEST. 

Correct? 

‰

 

Settings board (54), connector J2, terminals 3(+) - 2(-) = +15 Vdc; terminals 1(+) - 2(-) = -15 

Vdc. 

 
 YES 
 
 NO 

♦

 

Check the wiring between J2 settings board (54) and current transducer on pilot 
arc board (58). 

♦

 

With Power Source off, temporarily disconnect the connector J2 from settings 
board (54) and check the resistance between the terminals 3-2 and 1-2 of the patch 
connector disconnected from J2. Correct values = approximately 47 Kohm 
(terminals 3-2) and approximately 17 Kohm (terminals 1-2). If incorrect, replace 
pilot arc board (58). 

♦

 

Power up the Power Source again, keeping J2 disconnected from settings board 
(54), and check voltages on J2 of settings board (54), terminals 3(+) and 2(-) = 
+15 Vdc; terminals 1(+) and 2(-) = -15 Vdc. If incorrect, replace settings board 
(54). 

♦

 

Check supply voltages of the settings board (54), performing if necessary the 
SETTINGS BOARD (54) POWER SUPPLY TEST in par. 3.3.1.. 

♦

 

Replace settings (54) and/or pilot arc (58) boards. 

 

POWER SOURCE OUTPUT CURRENT SIGNAL TEST. 

Correct? 

‰

 

Settings board (54), connector J2 terminal 4(+) – 2(-) = fig. 5.2.2 = approxi0.5 Vdc 

(Power Source output current feedback signal with pilot arc lit), for a duration of 1 second 
(maximum pilot arc time) with start command activated. 

 
 YES 
 
 NO 

♦

 

Check the wiring between J2 settings board (54) and current transducer on pilot 
arc board (58). 

♦

 

With Power Source off, temporarily disconnect the connector J2 from settings 
board (54) and check the resistance between terminals 4 and 2 of J2 on settings 
board (54). Correct value = approximately 10 Kohm. If incorrect, replace settings 
board (54). 

♦

 

Replace settings (54) and/or pilot arc(58) boards. 

♦

 

Replace settings (54) and/or control (38) and/or pilot arc (58) boards. 

3.302.218 

9/8/2006 

Содержание PLASMA PROF 164 HQC
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды