manualshive.com logo in svg

Cebora PLASMA PROF 164 HQC, Руководство по обслуживанию

Поделиться
Скачать
Cebora PLASMA PROF 164 HQC Скачать руководство пользователя страница 24

CEBORA S.p.A.

 

24 

♦

 

With Power Source off, temporarily disconnect the connectors J4, J5, J6 and J7 
from solenoid valve board (2) and check the resistance on the terminals of the 
solenoid valve coils. Correct value = approximately 12 ohm (27 ohm for V10 on 
Console FPGC-2). If >Mohm (circuit interrupted), replace the solenoid valve 
involved. 

♦

 

Replace any defective solenoid valves, locating them with the aid of the table and 
fig. 2.6.1. 

♦

 

Check the wiring between the solenoid valves and the connectors J4, J5, J6 and J7 of solenoid 
valve board (2). 

♦

 

Check the wiring between J3 of solenoid valve board (2) and J7 of panel board (20). 

♦

 

Make sure communication between Power Source and Gas Console, performing if necessary 
the tests in par. 3.3.3.. 

♦

 

Check the Gas Console power supply, performing if necessary the TRANSFORMER (56) 
POWER SUPPLY TEST and GAS CONSOLE POWER SUPPLY TEST in par. 3.3.1. 

♦

 

With Power Source off, temporarily disconnect the connectors J4, J5, J6 and J7 from solenoid 
valve board (2) and check the resistance on the terminals of the solenoid valve coils. Correct 
value = approximately 12 ohm (27 ohm for V10 on Console FPGC-2). If 0 ohm, (short-
circuit) replace the  defective solenoid valve and solenoid valve board (2). 

♦

 

Replace the solenoid (2) and/or panel (20) boards. 

3.302.218 

9/8/2006 

Содержание PLASMA PROF 164 HQC
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды