CDA HN9841FR Скачать руководство пользователя страница 23

Страница: 23 / 32

Troubleshooting

On switching on

You observe that

Possible Causes

What should you do?

The hob does not work and

the lights on the control panel

do not switch on

The hob is not

connected to the

power supply or the

power supply is faulty

Check the electrical

circuit breaker and fuses

The hob is not working and the

display shows a non-standard

graphic

The electronics

are not functioning

correctly

Call CDA Customer Care

The hob is not working and the

display shows

The safety key lock

is on

Switch off the safety key

lock (see page 7)

fast frying steaks

Problem

Possible Causes

Possible Remedy

The appliance does not

work and no indicators are

lit.

The appliance has no

power

Check the fuse and

replace if blown.

Sensor fields do not

respond when touched.

Appliance is not turned on

A sensor field has been

touched too briefly (less

than a second)

Multiple sensors have been

touched/covered at the

same time

The safety key lock is

engaged

Turn on the appliance

Touch the sensor field

again and for longer

Only touch one sensor

field at a time unless

instructed otherwise

Disengage the safety

key lock as per page 18

The appliance does not

respond and emits an

extended beep

Improper use (wrong

sensor fields touched or

touched too briefly)

Switch the appliance off

via the on/off sensor and

at the mains and then

switch the power and

appliance on again

The appliance switches

itself off

No heat level has been

set within 10 seconds of

activating the appliance

Sensor fields covered or

dirty

Switch on the appliance

and set zone and heat

setting without delay

Uncover or clean the

sensor fields

A cooking zone switches

itself off and a residual heat

indicator is shown.

Operating time limiter has

activated.

Sensor fields covered or

dirty

Electronic components

have overheated

Nothing (see page 10)

Uncover or clean the

sensor fields

Nothing. Allow appliance

to cool.

Содержание HN9841FR

































Результаты поиска

Содержание HN9841FR

Отзывы:

Похожие инструкции для HN9841FR

Бренды по названию

Популярные бренды

CDA HN9841FR, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание HN9841FR

Отзывы:

Похожие инструкции для HN9841FR

Бренды по названию

Популярные бренды