background image

4

REVO S 

2PH from 60A to 800A - 690V

 

User’s manual

Important warnings for safety

This chapter contains important information for the safety. The not observance of these instructions may result 
in serious personal injury or death and can cause serious damages to the Thyristor unit and to the components 
system included.

The installation should be performed by qualified persons.

In the manual are used symbols to give more evidence at the notes of safety and operativity for the attention 
for the user:

This icon is present in all the operational procedures where the Improper 
operation may result in serious personal injury or death by Electrical Shock 
Hazard Symbol (a lightning bolt in a triangle) precedes an electric shock hazard 
CAUTION or WARNING safety statement.

Warning or Hazard that needs further explanation than the label on unit can 
provide. Consult User’s Guide for further information.

 

Unit is compliant with European Union directives.
See Declaration of Conformity for further details on Directives and Standards 
used for Compliance.

If available, unit is a Listed device per Underwriters Laboratories. It has been 
investigated to ANSI/UL® 508 standards for Industrial Control Switches and 
equivalent to CSA C22.2 #14.
For more detail search for File E231578 on www.ul.com

ESD Sensitive product, use proper grounding and handling techniques when 
installing or servicing product.

Do not throw in trash, use proper recycling techniques or consult manufacturer 
for proper disposal.

“NOTE”

 marks a short message to alert you to an important detail.

“CAUTION”

 safety alert appears with information that is important for protecting your equipment and 

performance. Be especially careful to read and follow all cautions that apply to your application.

“WARNING” 

safety alert appears with information that is important for protecting you, others and equipment 

from damage. Pay very close attention to all warnings that apply to your application.

Safety notes

WARNING! 

To avoid damage to property and equipment, injury and loss of life, adhere to applicable 

electrical codes and standard wiring practices when installing and operating this product. Failure to do 
so could result in damage, injury and death.

AVERTISSEMENT! 

Pour éviter d’endommager la propriété et l’équipement, les blessures et la perte 

de vie, respecter les codes électriques en vigueur et les pratiques de câblage standard au moment 
de l’installation et de l’utilisation de ce produit. Dans le cas contraire, cela peut entraîner la mort, des 
blessures graves ou des dommages.

IND. CONT. EQ.

E231578  2RD5

Содержание REVO S 2PH

































Отзывы: