33
4
Manual Control
Inputting an External Trigger
Refer to 7. Signal Input Sequence for the sequence diagram.
5
Locking Settings
When the setting switch is pressed for
2 seconds or longer, the lighting mode and
light intensity settings are locked, and
the LOCK setting indicator lights. (The set
values can be viewed.) Pressing the switch
again for 2 seconds or longer releases the lock.
2
Selecting the Channel
Press the channel selection switch to select the
channel to set (L1 to L3). The channel indicators
will change.
3
Setting the Light Intensity
Press the setting switch to light the BRT setting
indicator.
Turn the setting switch to set a value between 0 and 255.
(Default setting: 000, Minimum: 000, Maximum: 255)
* The Light Units are light dimly at the minimum value.
1
Setting the Manual/External Mode
Selector to Manual
Set the Manual/External Mode Selector to MANU
to set Manual Mode.
Make sure that the LOCK setting indicator is not light and that the trigger
logic switch is set to HIGH. Otherwise you may not be able to perform the
rest of this procedure.
Check
4
Selecting the Lighting Mode
Press the setting switch to light the PLS
setting indicator.
Turn the setting switch to select the lighting
mode from Continuous Mode, ON/OFF Mode,
or Strobe Mode.
(Default value: F00 )
Continuous Mode
Turn the setting switch and set F00 to
turn ON the Light Units continuously.
ON/OFF Mode
(If the external trigger is not used, the Light Units are ON continuously.)
Turn the setting switch and set F00 to turn the Light Units ON and OFF.
The Light Units are turned ON or OFF according to the external trigger signal input.
Strobe Mode
(If an external trigger is not used, the Light Units are OFF.)
To flash the strobe, turn the setting switch and
select a setting from F01 to F10
(strobe time of 40 μs to 40 ms).
The Light Units are turned ON for the period of time set
on the setting switch after the external trigger signal is input.
For details on the external trigger input, refer to 8. Inputting the External Trigger.
Digital display
F00
F01 F02 F03 F04 F05 F06 F07 F08 F09 F10
40 μs 80μs 120 μs 200 μs 600 μs
Strobe Mode
1 ms 4 ms 10 ms 20 ms 40 ms
Continuous Mode
ON/OFF Mode
Status
Make sure that the main power source is turned ON.
Set items , , and when using Continuous Mode or ON/OFF Mode.
Set items , , , and when using Strobe Mode.
1
3
4
2
1
3
2
Input Signal and Photocoupler
The input signal from the external trigger input connector can be used to control
the photocoupler inside the Unit to turn the LED Light Units ON and OFF or to
control strobe timing.
The operation depends on the setting of the trigger logic switch.
Setting Procedures
With the external trigger input connector pins 1
to 3, select the channels (L1 to L3) where you
want to input an external trigger, and input the
trigger.
Connector Layout
External Trigger Signal Connection Example
Trigger signals are input from the external trigger
input connector in ON/OFF Mode and Strobe
Mode are regardless of either Manual Mode or
External Mode.
ON/OFF Mode
The Light Units are turned ON or OFF according to
the external trigger signal input.
Strobe Mode
The Light Units are turned ON for the set time
after the external trigger signal is input.
9 7 5 3 1
10 8 6 4 2
1
2
3
Trigger Logic
Switch
ON/OFF
Mode
Input signal
HIGH
OFF
Light Units ON
Light Units ON for the set time.
LOW
ON
Light Units OFF
No change
HIGH
OFF
Light Units OFF
No change
LOW
HIGH
LOW
ON
Light Units ON
Light Units ON for the set time.
Photocoupler
Strobe Mode
External Trigger Input Connector Plug
Enlarged Cable Diagram
Rated input voltage: 24 VDC
Maximum input voltage: 26.4 VDC
ON voltage/ON current: 14.4 VDC min./3 mA max.
OFF voltage/OFF current: 5 VDC max./1 mA max.
ON/OFF response time: 10 µs max.
Input impedance: 12 kΩ (per terminal)
Signal Specifications
Pink
Red 1
Example: Pin No. 10, pink, red 1
Light Unit ON/OFF
control input
L1
24 VDC
Transistor (NPN)
open collector
Transistor (NPN)
open collector
Transistor (NPN)
open collector
PD3 Control Unit
External Circuits
L3
L2
10
1
2
3
10
()
Light Unit ON/OFF
control input
Light Unit ON/OFF
control input
No.
Wire color
Cable
(EXCB2-M10-3/EXCB2-M10M20-3)
Marks
Signal
Light Unit ON/OFF control input (L1)
Light Unit ON/OFF control input (L2)
Light Unit ON/OFF control input (L3)
Not used.
- - -
- - -
Orange
Orange
Gray
Pink
Black 1
Red 1
Black 1
Red 1
1
2
3
4 to 9
10
12kΩ
22kΩ
12kΩ
22kΩ
12kΩ
22kΩ
