background image

RRS-3 WL 
Installation and Operation

 

5

 

 

2

 

Operation 

A

TTENTION

Please ensure that all cables are clear of moving parts. Failure to do so may result in damage 
to cables and/or actuator. 

A

TTENTION

Please ensure that the batteries to the RSO-IV are fully charged or that the unit is plugged into 

AC power.  

For detailed instructions on the operation of the RSO-IV please see the RSO-IV Manual. 

1.

 

Ensure that the RRS-3 is properly installed. See the In-
stallation section of this manual for detailed instruc-

tions. 

2.

 

Connect the cable from the RSO-IV to the motor control 

box on the RRS-3 

3.

 

Turn the power switch on the RSO-IV to the ON position. 

4.

 

Program the settings for the RRS-3 into the RSO-IV.  

These settings can be found on the placard on the RRS-

3.  For more information on programming the RSO-IV 

please refer to the RSO-IV Technical Manual. 

5.

 

Exit the arc flash boundary. 

6.

 

Once the current limits have been properly set, press 

and release the REMOVE button on the RSO-IV control 

panel or remote pendant to rack the breaker out. 

7.

 

Press and release  the INSTALL button on the RSO-IV 

control panel or remote pendant to rack the breaker in. 

Содержание RRS-3 WL

















Отзывы: