background image

E-5

Regulatory Information

The USA and Canada

For Users in Canada

These Class A digital apparatuses comply with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject 

to the following two conditions: (1) this device may not cause interference, and (2) this device must 

accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio 

exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit 

pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélec

-

trique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

Caution Exposure to radio frequency radiation

To comply with FCC/IC RF exposure compliance requirements, this device must not be co-located 

or operating in conjunction with any other antenna or transmitter except in accordance with the FCC/

IC multi-transmitter product procedures or as described in the filing.

Précaution Exposition aux champs de radiofréquences

Pour respecter les normes relatives aux radiofréquences FCC/IC, ce dispositif ne doit pas être situé 

ou utilisé à proximité d’une autre antenne ou d’un autre émetteur si ce n’est selon les procédures 

mentionnées pour le multi-transmetteur FCC/IC ou décrites dans la documentation.

Caution Exposure to radio frequency radiation

To comply with FCC RF exposure compliance requirements, this device must not be co-located or 

operating in conjunction with any other antenna or transmitter except in accordance with the FCC 

multi-transmitter product procedures or as described in the fi ling.

FCC WARNING:

 Changes or modifications not expressly approved by 

the party responsible for compliance could void the user’s authority to operate 

the equipment.

WARNING:

This equipment has been tested and found to comply with the limits for 

a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed 

to provide reasonable protection against harmful interference when the equipment is 

operated in a commercial environment. This equipment generates, uses, and can radiate 

radio frequency energy and, if not installed and used in accordance with the instruction 

manual, may cause harmful interference to radio communications. Operation of this 

equipment in a residential area is likely to cause harmful interference in which case 

the user will be required to correct the interference at his own expense.

GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THE UNIT IN THE U.S.A.

                                          (Not applicable to other areas)

This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must
accept any interference received, including interference that

may cause undesired operation.

Содержание V-R7100




































Отзывы: