Operation Guide 3402
E-19
To configure the countdown timer
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down
A
until the current
countdown start time starts to flash, which indicates the
setting screen.
•
If the countdown start time is not displayed, use the
procedure under “To use the countdown timer”
(page E-21) to display it.
2. Press
C
to move the flashing in the sequence shown
below to select other settings.
Hours
Progress Beeper
Minutes
Auto-repeat
E-18
Countdown End Beeper
The countdown end beeper lets you know when the countdown reaches zero.
•
When the progress beeper is turned off, the countdown end beeper sounds for
about 1
0
seconds, or until you press any button to stop it.
•
When the progress beeper is turned on, the countdown end beeper sounds for
about one second.
Progress Beeper
When the progress beeper is turned on, the watch uses beeps to signal countdown
progress as described below.
•
Starting from five minutes before the end of the countdown, the watch emits four
short beeps at the top of each countdown minute.
•
3
0
seconds before the end of the countdown, the watch emits four short beeps.
•
The watch emits a short beep for each of the last 1
0
seconds of the countdown.
•
If the countdown start time is six minutes or greater, the watch emits a short beep for
each second of the final 1
0
seconds before the five-minute point is reached. Four
short beeps are emitted to signal when the five-minute point is reached.
E-17
Auto-repeat
When auto-repeat is turned on, the countdown restarts automatically from the
countdown start time when it reaches zero.
When auto-repeat is turned off, the countdown stops when it reaches zero and the
display shows the original countdown start time.
•
Pressing
D
while an auto-repeat countdown is in progress pauses the current
countdown. You can resume the auto-repeat countdown by pressing
D
, or you can
press
A
to reset to the countdown time starting value.
Countdown Timer Beeper Operations
The watch beeps at various times during a countdown so you can keep informed
about the countdown status without looking at the display. The following describes the
types of beeper operations the watch performs during a countdown.
E-16
Countdown Timer
The countdown timer can be set within a range of one
minute to 24 hours. An alarm sounds when the countdown
reaches zero. The countdown timer also has an auto-
repeat feature and a progress beeper that signals the
progress of the countdown.
•
All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C
(page E-7).
Configuring the Countdown Timer
The following are the settings you should configure before
actually using the countdown timer.
Countdown start time; Auto-repeat on/off; Progress
beeper on/off
•
See “To configure the countdown timer” (page E-19) for
information about setting up the timer.
Seconds
Hours
Minutes
E-15
About Auto-Start (Stopwatch Mode (ST1))
With Auto-Start, the watch performs a 5-second countdown, and stopwatch operation
starts automatically when the countdown reaches zero.
During the final three seconds of the countdown, a beeper sounds with each second.
To use Auto-Start (ST1)
1. While the stopwatch screen is showing all zeros in the
Stopwatch Mode, press
A
.
•
This displays a 5-second countdown screen.
•
To return to the all zeros screen, press
A
again.
2. Press
D
to start the countdown.
•
When the countdown reaches zero, a tone sounds and
a stopwatch timing operation starts automatically.
•
Pressing
D
while the Auto-Start countdown is in
progress starts the stopwatch immediately.
E-14
To measure times with the stopwatch
(Stopwatch Mode (ST1) and Stopwatch Mode (ST2))
Elapsed Time
Start
Stop
Re-start
Stop
Clear
Start
Split
(
displayed)
Split release
Stop
Clear
Start
Split
Stop
Split release
Clear
Split Time
Two Finishes
First runner finishes.
Display time of first
runner.
Second runner
finishes.
Display time of
second runner.
E-13
Stopwatches
Your watch has two stopwatch modes:Stopwatch Mode
(ST1) and Stopwatch Mode (ST2). Both stopwatch modes
let you measure elapsed time, split times, and two
finishes. The Stopwatch Mode (ST1) includes Auto-Start.
•
A display range of the stopwatch is 999 hours,
59 minutes, 59.99 seconds.
•
A stopwatch continues to run, restarting from zero after
it reaches its limit, until you stop it.
•
A stopwatch measurement operation continues even if
you exit a Stopwatch Mode.
•
Exiting a Stopwatch Mode while a split time is frozen on
the display clears the split time and returns to elapsed
time measurement.
•
All of the operations in this section are performed in the
Stopwatch Mode (ST1) or Stopwatch Mode (ST2), which
you enter by pressing
C
(page E-6).
Seconds
Minutes
1/100 second
Timekeeping Mode time
*
During stopwatch elapsed
time measurement,
shows the number of
hours elapsed.
E-12
To toggle between 12-hour and 24-hour timekeeping
In the Timekeeping Mode, press
D
to toggle between 12-hour timekeeping and 24-
hour timekeeping.
•
With the 12-hour format, the
P
(PM) indicator appears to the left of the hour digits for
times in the range of noon to 11:59 p.m. and no indicator appears to the left of the
hour digits for times in the range of midnight to 11:59 a.m.
•
With the 24-hour format, times are displayed in the range of
0
:
00
to 23:59, without
any indicator.
•
The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
•
The
P
indicator is not displayed when the current time is displayed in other modes.
E-11
4. Press
A
to exit the setting screen.
•
The day of the week is displayed automatically in accordance with the date (year,
month, and day) settings.
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from Standard
Time. Remember that not all countries or even local areas use Daylight Saving Time.
To toggle the Timekeeping Mode time between DST and Standard Time
1. In the Timekeeping Mode, hold down
A
until the
seconds start to flash, which indicates the setting
screen.
2. Press
C
to display the DST setting screen.
3. Press
D
to toggle between Daylight Saving Time
(
displayed) and Standard Time (
displayed).
4. Press
A
to exit the setting screen.
•
The
DST
indicator appears on the display to indicate
that Daylight Saving Time is turned on.
DST indicator
E-1
0
3. When the setting you want to change is flashing, use
D
and
B
to change it as
described below.
•
For details about time zones, see the “City Code Table” at the back of this manual.
•
See “Daylight Saving Time (DST)” on page E-11 for details about DST setting.
Screen
To do this:
Reset the seconds to
Toggle between Daylight Saving Time
(
) and Standard Time (
)
Specify your Home Time zone
Change the hour or minutes
Change the year
Change the month or day
Do this:
Press
D
.
Press
D
.
Use
D
(eastward) and
B
(westward).
Use
D
(+) and
B
(–).
