Operation Guide 2894
1
MO0912-EB
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out
of your purchase, be sure to read this manual carefully and keep it on hand
for later reference when necessary.
Applications
The built-in sensors of this watch measure direction, barometric pressure,
temperature and altitude. Measured values are then shown on the display.
Such features make this watch useful when hiking, mountain climbing, or
when engaging in other such outdoor activities.
Keep the watch exposed to bright light
The electricity generated by the solar cell of the
watch is stored by a built-in battery. Leaving or
using the watch where it is not exposed to light
causes the battery to run down. Make sure the
watch is exposed to light as much as possible.
•
When you are not wearing the watch on your
wrist, position the face so it is pointed at a
source of bright light.
•
You should try to keep the watch outside of
your sleeve as much as possible. Even if the
face of the watch is only partially blocked from
light, charging will be reduced significantly.
ll
l
l
l
l
l
l
l
l
l
Bright light
Solar cell
•
Frequent display illumination can run down the battery quickly and require
charging. The following guidelines give an idea of the charging time
required to recover from a single illumination operation.
Approximately 5 minutes exposure to bright sunlight coming in through a
window
Approximately 50 minutes exposure to indoor fluorescent lighting
•
Be sure to read “Power Supply” for important information you need to
know when exposing the watch to bright light.
If the display of the watch is blank...
If the display of the watch is blank, it means that the watch’s Power Saving
function has turned off the display to conserve power.
•
See “Power Saving” for more information.
•
The watch continues to operate, even when it is not exposed to light.
Leaving the watch in the dark can cause the battery to run down, which will
cause some watch functions to be disabled. If the battery goes dead, you
will have to re-configure watch settings after recharging. To ensure normal
watch operation, be sure to keep it exposed to light as much as possible.
Bright light
Electrical
energy
All
functions
enabled
LEVEL 1
LEVEL 2
LEVEL 3
LEVEL 4
Charge
Solar cell
(Converts light to
electrical power.)
Rechargeable battery
LEVEL 1
LEVEL 2
LEVEL 3
LEVEL 4
Some
functions
disabled
Dis-
charge
Battery charges in the light.
Battery discharges in the dark.
Warning!
•
The measurement functions built into this watch are not intended for
taking measurements that require professional or industrial precision.
Values produced by this watch should be considered as reasonable
representations only.
•
When engaging in mountain climbing or other activities in which losing
your way can create a dangerous or life-threatening situation, always be
sure to use a second compass to confirm direction readings.
•
CASIO COMPUTER CO., LTD. assumes no responsibility for any loss,
or any claims by third parties that may arise through the use of this
watch.
About This Manual
•
Button operations are indicated using the
letters shown in the illustration.
•
Each section of this manual provides you with
the information you need to perform operations
in each mode. Further details and technical
information can be found in the “Reference”
section.
(Light)
General Guide
•
The illustration below shows which buttons you need to press to navigate
between modes.
•
In any mode, press
L
to illuminate the display.
•
You can use buttons
A
,
B
, and
C
to directly enter a sensor mode from
the Timekeeping Mode or from another sensor mode. To enter a sensor
mode from the Data Recall, World Time, Stopwatch, Countdown Timer, or
Alarm Mode, first enter the Timekeeping Mode and then press the
applicable button.
Timekeeping Mode
Altimeter Mode
World Time
Mode
Data Recall
Mode
Digital
Compass Mode
Press
D
.
▲
▲
Press
B
.
Countdown
Timer Mode
Press
D
.
▲
Press
A
.
▲
Sensor Modes
▲
▲
Stopwatch Mode
▲
Barometer/
Thermometer Mode
Press
C
.
Alarm Mode
▲
▲
▲
Timekeeping
Use the Timekeeping Mode to set and view the
current time and date.
•
In the Timekeeping Mode, press
E
to toggle
between the month–day and the day of the
week at the top of the display.
Read This Before You Set the Time and
Date!
This watch is preset with a number of city codes,
each of which represents the time zone where
that city is located. When setting the time, it is
important that you select the correct city code for
your Home City (the city where you normally use
the watch). If your location is not included in the
preset city codes, select the preset city code that
is in the same time zone as your location.
Hour : Minutes
PM indicator
Seconds
Month – Day
Day of week
Press
E
.
•
Note that all of the times for the World Time Mode city codes are displayed
in accordance with the time and date settings you configure in the
Timekeeping Mode.
•
After you correctly set your Home City time and date, you can set the watch
up for timekeeping with a different city code simply by changing the Home
City code in the Timekeeping Mode.
To set the time and date
1. In the Timekeeping Mode, hold down
E
until the city code starts to flash,
which indicates the setting screen.
2. Use
C
and
A
to select the city code you want.
•
Make sure you select your Home City code before changing any other
setting.
•
For full information on city codes, see the “City Code Table”.
•
The actual level at which some functions are disabled depends on the
watch model.