manualshive.com logo in svg

Case 580SR, Руководство по обслуживанию

Case 580SR - универсальный погрузчик с задним расположением двигателя. Скачайте бесплатное руководство по обслуживанию и ремонту на manualshive.com. Получите подробные инструкции и советы по эксплуатации вашего оборудования. Надежный и эффективный партнер для рабочих задач.

Поделиться
Скачать
background image

SECTION 55 - ELECTRICAL SYSTEM

153

CHECKING THE ALTERNATOR COMPONENTS

Checking of components must be done only if the
PRELIMINARY TESTS reveal an alternator defect
which relates to the following components:

Z

Regulator

Z

Continuity of the rotor field winding

Z

Brushes, springs and slip rings

NOTE: 

these checks may be carried out without re-

moving the alternator from the vehicle.
The alternator must be removed to check the other
components of the alternator.
Refer to the “Removal” section in this chapter. 

IMPORTANT: 

before disconnecting the cables from

the alternator, make sure that the ignition is turned
off (key on “off”) and the negative cable of the battery
is disconnected. 

Required devices:

Z

12 V battery

Z

Multimeter

Z

2.2 W test lamp

CHECKING THE REGULATOR AND THE FIELD 

CIRCUIT OF THE REGULATOR

Z

Disconnect all cables from the alternator.

Z

Connect a 12 V battery and a 2.2 W test lamp (2) in
series between terminal L (1) and the alternator
body (negative side on body).

Z

The test lamp must turn on.

If the lamp does not turn on, the rotor circuit is defec-
tive. Check the brushes, the slip rings and the conti-
nuity of the rotor field windings.
If the inspection reveals that these components are
in good condition, the defect may be due to the reg-
ulator.

CHECKING THE CONTINUITY OF THE ROTOR 

FIELD WINDING

Z

Remove the regulator with the brush holder. 

Z

Connect an ohmmeter (3) between the two slip
rings (2). The resistance must be 2.6 ohms at
20 °C.

If the resistance is not correct, replace the rotor (1)
as described in the “Removal” section below.

Copyright ©

Содержание 580SR













































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 580SR

AmeriGlide Victorian Outdoor Elevator Installation Manual preview
Victorian Outdoor Elevator
Бренд: AmeriGlide Страницы: 39
SANY SY365C LC Operation And Maintenance Manual preview
SY365C LC
Бренд: SANY Страницы: 276
Savaria Orion Planning Manual preview
Orion
Бренд: Savaria Страницы: 28
IHI IC50 Operation Manual preview
IC50
Бренд: IHI Страницы: 104
Menzi Muck Menzi IHI 45v4 Operator'S Manual preview
Menzi IHI 45v4
Бренд: Menzi Muck Страницы: 147
Hyundai Robex 290LC-9MH Service Manual preview
Robex 290LC-9MH
Бренд: Hyundai Страницы: 41

Бренды по названию

Популярные бренды

Загрузить еще бренды