Case 580SR Скачать руководство пользователя страница 929 | Manualshive

Страница: 929 / 1068

background image

SECTION 55 - ELECTRICAL SYSTEM

101

6.

HYDRAULIC SPEED CONTROL SWITCH (If
fitted)
This switch enables an increase in the moving
speed of the loader and backhoe attachment.

7.

“GLIDE RIDE” SWITCH (Optional)
The “glide ride” system control improves the ma-
chine comfort during travel, regardless of the
type of terrain and with the loader bucket full or
empty. It reduces forward and rearward pitching
when moving to the rear or forwards and when
carrying loads, at the same time increasing pro-
ductivity and operator comfort. It also reduces
impact forces to the machine during operation.
Do not use this system while operating the load-
er attachment.

8.

MANUAL MODE SELECTION SWITCH
(Powershift transmission)
In situations where manual gearshifting (up or
downshift) is required, the automatic gearshift of
the powershift transmission can be overridden
by means of this switch.

NOTE:

changing gears up or down must always be

done using the powershift transmission lever.

When the manual mode is no longer required, place
the switch back to the OFF position to return to au-
tomatic gearshifting.

9.

HORN BUTTON
(Powershift transmission)
This hold-down switch operates the warning
horn.

10.

HAZARD LIGHT SWITCH
Press the control down to locked position. The
direction indicators and the control will flash si-
multaneously.
Press the control down again to turn off the di-
rection indicators and the indicator lamp.

S

WARNING

S

Never operate the “glide ride” system control when
the loader arm and loader bucket are maintaining
the front of the machine raised off the ground. The
machine could fall and cause serious or fatal injury.

Copyright ©

«
...
927
928
929
930
931
...
»

Содержание 580SR













































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 580SR

Бренд: ThyssenKrupp Страницы: 7

Бренд: Case Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды