manualshive.com logo in svg

Case 580SR, Руководство по обслуживанию

Case 580SR - универсальный погрузчик с задним расположением двигателя. Скачайте бесплатное руководство по обслуживанию и ремонту на manualshive.com. Получите подробные инструкции и советы по эксплуатации вашего оборудования. Надежный и эффективный партнер для рабочих задач.

Поделиться
Скачать
background image

SECTION 21 - TRANSMISSION

125

CONTROL VALVE OPERATION FORWARD, SECOND GEAR WITH 4WD ENGAGED

Pressure oil from the system regulating valve flows to the pressure reducing valve.
The pressure lowers to 5.5 bar. This oil flows to the 6 solenoids.
Oil also supplies the modulation valve.
When the powershift lever is moved forward and twisted anti clock wise a electrical signal is sent to:

Z

Oil flows from the system pressure regulating valve at 20 bar through the 4WD spool to engage the 4WD 
clutch.

Z

System pressure also flows through the range modulation valve, then through the 1st 2nd spool to engage 
the 2nd gear clutch.

Z

The high low solenoid which energizes allowing pilot oil to flow to the shift spool. This will allow oil to flow to 
the low clutch.

Z

The neutral forward solenoid which energizes allows pilot pressure to flow to the shift spool this will allow oil 
to flow on to the forward low shift spool.

Z

The modulation valve has a reducing current from the microprocessor, pilot pressure gradually increases act-
ing on the boost valve and it multiplies pilot pressure.

Z

The oil from the boost valve is modulated allowing a steady increase of pressure to act on the forward low 
clutch pack which gradually takes up drive until clutch pressure reaches 20 bar.

1.

Transmission sump

2.

Transmission breather

3.

Suction strainer

4.

Gerotor oil pump

5.

Pressure oil filter

6.

Filter by-pass valve 4.3 bar

7.

System pressure test port 20 bar

8.

System pressure regulating valve 20 bar

9.

Oil to converter system

10.

Pressure reducing valve 5.5 bar

11.

2nd/1st Solenoid

12.

2nd/1st shift spool

13.

2nd gear clutch

14.

1st gear clutch

15.

Range modulation solenoid

16.

Range modulation spool

17.

Range modulation restriction

18.

4WD solenoid

19.

4WD shift spool

20.

4WD clutch

21.

High/low solenoid

22.

High/low shift spool

23.

Forward high clutch

24.

Forward low clutch

25.

Neutral reverse solenoid

26.

Neutral reverse shift spool

27.

Reverse clutch

28.

Neutral forward solenoid

29.

Neutral forward shift spool

30.

Electronic modulation valve 0-5.5 bar

31.

Accumulator

32.

Pressure booster 0-20 bar

Copyright ©

Содержание 580SR













































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 580SR

Komatsu PW160-7K Series Operation And Maintenance Manual preview
PW160-7K Series
Бренд: Komatsu Страницы: 358
ELGO-PLUS SpringerMAX-PRO Instruction preview
SpringerMAX-PRO
Бренд: ELGO-PLUS Страницы: 37
Ditch Witch RT45 Operator'S Manual preview
RT45
Бренд: Ditch Witch Страницы: 199
jcb JZ 70 Service Manual preview
JZ 70
Бренд: jcb Страницы: 360
Yuchai YC15-8 Operation And Maintenance Manual preview
YC15-8
Бренд: Yuchai Страницы: 157

Бренды по названию

Популярные бренды

Загрузить еще бренды