background image

12

SAFETY FIRST

Changes or modifications not expressly ap-
proved in writing by Casablanca Fan Co. may
void the user’s authority to operate this
equipment.

This device complies with RSS-210 of Industry Canada. Operation is subject to
the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.

2

Warning

:

 To reduce the risk of electrical shock this fan must be installed with an isolating wall control switch.

W-72

CONTROL

HOLDER

SCREW

6-32 X 1”

(2)

SCREW

6-32 X 

3

/

8

(2)

WOOD

SCREW
1” (2)

DRYWALL

ANCHOR

6-32 (2)

12V BATTERY

W-72

CONTROL

VERSA•TOUCH 2 

 INSTALLATION

VERSA•TOUCH 2 

 CONTROL BRACKET INSTALLATION

Standard Light Switch
Step A.

  Remove the two screws holding the switch cover

plate. Do not remove the cover plate.

Step B.

 Orient the control bracket as shown and line up the

two inner mounting holes with those on the switch.

Step C.

 Install and tighten screws by 

hand 

only.

INNER

MOUNTING

HOLES

CONTROL

BRACKET

STANDARD

TOGGLE
SWITCH

SWITCH

COVER

PLATE

Rocker Light Switch
Step A.

 Break off the two tabs by pushing outward.

Step B.

 Remove the two screws holding the switch cover

plate. Do not remove the cover plate.

Step C.

 Orient the control bracket as shown and line up the

two inner mounting holes with those on the switch.

Step D.

 Install and tighten screws by 

hand 

only.

OUTER

MOUNTING

HOLES

CONTROL

BRACKET

ROCKER

TYPE

LIGHT

SWITCH

SWITCH

COVER

PLATE

Wall Installation
Step A.

 Locate a 2x4 wall

stud in a convenient
location.

Step B.

 Orient the control

bracket as shown over the
2x4 stud.

Step C.

  Use the 1” wood

screws in either the inner
or outer mounting holes.
Install and tighten screws
by 

hand 

only.

DECOR OVALHEAD SCREW

6-32 X 1”

ANCHOR

PANHEAD

SCREW

WOOD

SCREW 1”

DRYWALL ANCHOR

Note:

 The wall anchors and 6-32 x 1” screws may be

used in situations where mounting to a stud is not pos-
sible. Use the inner mounting holes. After securing the
anchor, discard the anchor’s pointed screws and use the
6-32 decor ovalhead screws supplied.

CAUTION! Do not use with wall dimmer.

Содержание Campana


















Отзывы: