UP
DOWN
SET
UX-HM2
UMC1000 HAND HELD MIC
1. BATTERY INSTALLATION
FIG. C
While holding the higher part of the transmitter body, unscrew the handle. Install fresh
AA alkaline batteries. Replace the handle and turn clockwise until tight.
2. POWER ON
FIG. D
Switch to POWER ON position.
3
.
MUTE SWITCH
FIG. D
Used to mute audio without losing RF connection.
4. UMC1000-ID 7 COLOR CODED RINGS
FIG. E
Use the
UMC1000-ID
7 color coded rings to identify multiple microphones in use.
Each color can correspond to a different wireless channel.
UBP1000 BELT-PACK TRANSMITTER
1. BATTERY INSTALLATION
FIG. A
Alkaline AA batteries are recommended. Hold on to the belt clip buttons to release battery
tray. Insert fresh AA alkaline batteries. Slide the belt clip back until it locks.
BELT PACK SET-UP
FIG. A
1. METAL CASE & BELT CLIP
The metal case provides extra protection for the transmitter and the plastic belt clip keeps
it safe and at your side. Hold on to the belt clip buttons and slide the transmitter up to access
the front and rear controls.
2. SENSITIVITY
FIG. B
The transmitter's sensitivity controls are located on the rear. Use
the mini screwdriver to first set the Sensitivity switch to 0 for instruments or -20 for micro-
phones. Use the mini screwdriver to make fine gain adjustments to the Sensitivity AF Gain
for optimal transmitter volume. Decrease the gain if distortion is heard.
3. INPUT CONNECTOR
The mini XLR input jack will connect a lavaliere mic, headset mic, or instrument cable to
the transmitter. Line up the notches on the side of the jack and plug. Push in until cable
locks into the jack. To unplug the mini XLR cable, press the round release button on the
cable to unlock it from the jack.
4. TRANSMITTER ON SWITCH
Turn the receiver volume down before turning the transmitter power ON. The transmitter
ON-OFF switch is located at the top of the unit.
5. FREQUENCY ADJUSTING
Hold "
SET
" button for 3 seconds to activate frequency.
Once you see "
MHZ
" blinking, you are ready to select your desired frequency by using
"
UP
" and "
DOWN
" buttons.
Press the "
SET
" button again to store your changes.
6. TO ACTIVATE "LOCK MODE"
Hold on to "
UP
" button for 3 seconds to activate
"LOCK MODE"
, press again to unlock.
Transmitter
ON/OFF Switch
Push round button
to release cable
LCD Display
SET Button(1)
UP Button
Down Button
Hold to release
battery tray
click sides
battery case
slides down
replace
batteries
push up to
access front and
rear controls
UX-HM2 HEADSET MIC
Connect the mic cable to the transmitter's mini XLR input jack. Place the mic on vocal-
ist head with the headband resting comfortably on the rear of the neck. Keep the mic
a minimum of 2 inches from the mouth. Adjust the mic position to minimize air from
hitting the mic.
UX-LP1 LAVALIERE MIC
Connect the Lavaliere mic cable to the transmitter's mini XLR input jack. Clip the mic
to a shirt. For optimum sound, position the mic as close to the mouth with the top of
the mic facing up. Test out various positions along the center of the chest to determine
the ideal mic placement. This may vary from person to person as each voice projects uniquely.
UXGT INSTRUMENT CABLE
Connect the cable to the belt-pack transmitter’s mini
XLR input jack. Plug the 1/4” connector into a guitar. Turn the receiver volume down
before turning the transmitter power ON.
UX-LP1
UXGT
PROGRAMMING HAND HELD MIC
FIG. F
1. SETTING GROUP CHANNEL
GROUP SET UP
Press "
SET
" button for three seconds until the "
MHZ
" shows and then
re-press "
SET
" until the group digit shows. Now you can
press "
UP
" or "
DOWN
" button one sec. to increase or decrease group
number
CHANNEL SET UP
Follow the
GROUP SET UP
procedures, then press "
SET
" again and the frequency displays,
press "
UP
" or "
DOWN
" to increase or decrease the frequency.
Press "
SET
" to store the mic frequency.
GROUP DISPLAYED
Press "
SET
" for three seconds until the Group digit shows. Then re-press "
UP
" or "
DOWN
"
button to increase or decrease the group number.
Press "
SET
" again and the frequency displays. Press "
UP
" or "
DOWN
" to increase or decrease
the frequency. Press "
SET
" again and the mic will store the frequency.
FIG. A
FIG. B
FIG. C
unscrew the
handle to
replace
batteries
POWER
FIG. D
MUTE
FIG. E
UMC1000-ID
color coded rings
FIG. F
Antenna
Sensitivity
-20 -6 0
GAIN
Set to 0 for
instruments
Set to -20 for mics
fine gain
settings