UX1000/UMC1000/UBM1000
SPECIFICATIONS:
RECEIVER UX1000
Receiving System
Diversity- PLL Synthesized
Stability
± 0.005%
Signal-to-noise >100 dB
Image Rejection
>60 dB
THD
≤
1% @ 1kHz
RF Sensitivity
-107dBµ for 12 dB S/N AD
Audio Output
-12 dBµ / 800 ohm -unbalanced
Output Conn.
Unbalanced 1/4” phone jack
Balanced XLR M-type
Power Supply
12-18V DC, 500 mA, with provided
AC adapter
Dimensions
8.307” (211 mm) W x 1.575” (40
mm) H x 5.394” (137 mm) D
Net Weight
2.3 lbs (1.05 kgs)
Accessories
Rack mount adapters, AC adapter
Warranty
90 days
CARVIN ENGINEERING DATA
OPERATING MANUAL
12340 World Trade Drive, San Diego, CA 92128
UX1000-MC, UX100BP WIRELESS SYSTEMS
Congratulations on your purchase of the
UX1000 SERIES
Professional Wireless
System.
These systems include a receiver along with a handheld mic with
transmitter
(UMC1000)
or a belt-pack transmitter
(UBP1000)
depending on the
model purchased.The headworn mic
(UX-HM2)
, cable for instrument
(UXGT)
and
lavaliere mic
(UX-LP1)
are all available as additional options to the
UBP1000
belt-pack system.
The receiver features true UHF diversity reception. Two antennas feed two
completely independent RF receivers on the same frequency. Automatic logic
circuitry continuously compares and selects the superior signal to provide better
sound quality and reduce the possibility of interference and dropouts. Both the
transmitter and receiver have 960 user selectable channels, which can be grouped
into four groups. The receiver can be mounted in a standard 19" rack (1U) with
use of the optional UX-DR adapter.
The versatile
UBP1000
belt-pack transmitter is designed for use with
condenser microphones as well as Hi-Z instrument pickups. Please note that in
multiple-system applications there must be one transmitter per receiver.
GETTING STARTED QUICKLY
If you’re like most new owners, you’re probably in a hurry to plug your wireless
system in and use it. Here are some brief instructions to get you going quickly.
With the wireless system unplugged and the unit turned off, complete the
following procedures:
1. CHANNEL CHECK
Check that both the transmitter and receiver are set
to corresponding channel. If multiple systems are used, each system must be
set to their own channel.
2. OUTPUT CONNECTIONS
There are two audio outputs on the back
of the receiver: balanced XLR and unbalanced 1/4”. Connect the appropriate
cables for your system.
3. POWER CONNECTIONS
Connect the included AC adapter to the DC
power input on the back of the receiver. Plug the adapter into a standard 120
volt 60 Hz AC power outlet.
4. RECEIVER POWER ON
Turn down the Volume control of the receiver as
well as the mixer. Switch on the receiver only. Do not switch on the transmitter.
The power indicator will light up even though the transmitter is not on.
5. BELT PACK SETTINGS
Connect the instrument cable or mic
to the Belt-pack. Set the rear gain switch to -20 for mic or 0 for instrument use.
Set the fine gain control to 12 o’clock. Reduce if distortion occurs.
HANDHELD MIC TRANSMITTER
UMC1000
Polar Pattern
Unidirectional
RF Power Output
3 mW
Spurious Emissions
Under federal regulations
Dynamic Range
≥
100 dB
Battery
AA 1.5v alkaline qty 2
Current Consumption
30 mA typical
Battery Life
Approx. 25 hours
Dimensions
9.65” long, 2.10” dia.
Net Wt (no battery)
12.7 oz (360 grams)
Accessory Included
mic clip
Warranty
90 days
BELT PACK TRANSMITTER UBM1000
Spurious Rejection
< -60 dBC
Stability
± 0.005%
Frequency Deviation
± 48kHz
Battery
AA 1.5v alkaline qty 2
S/N Ratio
>100dB (1kHz-A)
Current Consumption
100mA typical
Dimensions
2.56” W x 4” H x 1” D
Net Wt (no battery)
2.8 oz (78 grams)
Warranty
90 days
6. BATTERY
Insert fresh AA alkaline batteries into the transmitter.
7. TRANSMITTER POWER ON
Switch the transmitter mic to
the “on” position.
8. SOUND CHECK
To do a sound check, gradually raise the level while
watching the AF level indicator. Increase the level until the AF level indicator
peaks. This indicates that maximum level without distortion has been reached.
On the belt pack adjust the AF level of the transmitter using the included
screwdriver.
For your records, record the following information.
Serial No._____________________ Invoice Date_______________
RECEIVING INSPECTION—read before getting started
INSPECT YOUR WIRELESS SYSTEM FOR ANY DAMAGE which may have occurred
during shipping. If any damage is found, please notify the shipping company and
CARVIN immediately.
SAVE THE CARTON & ALL PACKING MATERIALS. In the event you have to re-ship
your unit, always use the original carton and packing material.This will provide the best-
possible protection during shipment. CARVIN and the shipping company are not liable
for any damage cause by improper packing.
SAVE YOUR INVOICE. It will be required for warranty service if needed in the future.
SHIPMENT SHORTAGE. If you find items missing, they may have been shipped
separately. Please allow several days for the rest of your order to arrive before inquiring.
RECORD THE SERIAL NUMBER on the enclosed warranty card or below on this manual for
your records. Keep your portion of the card and return the portion with your name and
comments to us.
c
rev A