UX1000 RECEIVER
FRONT PANEL FEATURES
1. POWER SWITCH
Depress to power the receiver.
2. UP BUTTON
Depress to increase the number and set the operation mode.
3. DOWN BUTTON
Depress to decrease the number and set the operation mode.
4. SET BUTTON
Depress to set up the operation mode.
5. LCD PANEL
Clearly displays the operation mode
6. VOLUME CONTROL
Adjusts the output audio level to your amp or mixer. If distortion occurs, reduce the level.
REAR PANEL FEATURES
7. DC POWER INPUT
Use AC power adapter, which supplies 12V DC.
8. UNBALANCED 1/4” AUDIO OUTPUT JACK
1/4” phone jack can be connected to an unbalanced input of a mixer.
9. BALANCED XLR AUDIO OUTPUT JACK
A standard XLR microphone cable can be used to connect the receiver output to a balanced
input on a mixer.
10
.
ANTENNA
Dual antenna for Diversity signal reception.
1.
AF signal
2
. RF signal
3.
Display for GROUP mode
4.
Display for LOCK mode
5.
Display for set FREQ. mode
6.
Frequency display
7.
Diversity display (A or B receiver)
8.
Battery display for the transmitter
9.
Group channel display
LCD PANEL DISPLAY
UX1000 FRONT AND REAR RECEIVER PANEL CONTROLS
7
8
9
2
6
5
4
1
3
1. SETTING GROUP CHANNEL
DISPLAYED
A. GROUP NUMBER SET UP
Press the "
SET
" button for three seconds until "
FREQ
" shows up in the LCD display.
Press the "
SET
" button a 2nd time to display the frequency number. Press "
UP
" or "
DOWN
"
to increase or decrease the group number.
B. CHANNEL SET UP
After step
A.
press "
SET
" a 3rd time to display “
CH”
, press "
UP
" or "
DOWN
" to change
the
CH
number. Press "
SET
" again and the receiver will store the channel.
DISPLAYED
GROUP NUMBER SET UP
Press the "
SET
" button for three seconds until the "
G
" group number shows in the LCD.
Press the "
SET
" button a 2nd time to display the frequency number. Press "
UP
" or "
DOWN
"
to increase or decrease the group number.
CHANNEL SET UP
After the group set up press "
SET
" a 3rd time to display “
CH”
, press "
UP
" or "
DOWN
"
to change the “
CH”
number. Press "
SET
" again and the receiver will store the channel.
2. SETTING FREQUENCY
DISPL
Press the "
SET
" button for three seconds until "
FREQ
" shows up in the LCD display.
Press "
UP
" or "
DOWN
" to increase or decrease the frequency number. Press "
SET
" again
and the receiver will store the frequency.
DISPLAYED
Press the "
SET
" button for three seconds until the "
G
" group number shows in the LCD.
Press "
SET
" again and the frequency starts flashing.
Press "
SET
" until the "
FREQ
" shows use the "
UP
" or "
DOWN
" buttons to change the group
digit. Press "
SET
" again the receiver will store the channel.
3. SETTING LOCK-ON
DISPLAYED
Press "
SET
" button for three seconds until "
FREQ
" shows in the LCD. Press "
SET
" again
and the Group number starts flashing. Press "
SET
" again until the frequency starts
flashing then press "
SET
" to start the lock-on setting.
Press "
UP
" button for lock-on mode and "
DOWN
" button for lock-off mode. Re-press
"
SET
" and the lock function will store.
DISPLAYED
Press "
SET
" button for three seconds until the Group number shows. Re-press "
SET
"
and the frequency starts flashing. Press "
SET
" again till "
FREQ
" show up, re-press "
SET
"
button till "
LOCK OFF
" starts flashing then you can proceed the lock-on setting.
(2) Press "
UP
"" button for lock-on mode and "
DOWN
" button for lock-off mode.
Re-press "
SET
" button the lock function will store.
4. RELIEVED LOCK-ON
Press "
SET
" button three seconds till "
LOCK ON
" show up, then press "
DOWN
" button
plus "
SET
" button to store the lock-on relieved.
5.
Pressing any button will display
"LOCK ON"
during Lock On mode. This setting remains
until it is disabled. Turning the unit off will not disable the Lock On mode.
GROUP
FREQ.
GROUP
FREQ.
GROUP
FREQ.
10
UX-DR DUAL RACKMOUNT ADAPTER
With the optional UX-DR adapter, you can mount
one or two receivers. Remove the front panel of the mounting adapter to mount the
second receiver.