background image

T

ABLE

 

OF

 C

ONTENTS

 

Introduction ......................................................................... 1 
Serial Number ..................................................................... 1 
Installing Control Unit .......................................................... 1 
Power and Battery Backup ................................................. 1 
Earth Ground ...................................................................... 1 
Trip-Test Button  ................................................................. 2 
Re-Trigger Hold-Off ............................................................ 2 
Transient Suppression ........................................................ 2 
Adjusting Sounder (Annunciator) Time ............................... 2 
Adjusting Probe Sensitivity ................................................. 2 
Extra Set of Relay Contacts ................................................ 2 
Connecting to a Gate Operator ........................................... 2 
Annunciation in the Home when used with Gate................. 3 
Integrating With a Security or Home Automation System ... 3 
CT-6 Probe and Wire Check-out ......................................... 3 
System and Probe Don'ts ................................................... 3 
Location of CT-6 Probe ....................................................... 4 
Installing CT-6 Probe and Cable ......................................... 4 
Connecting CT-6 Probe to Control Unit .............................. 5 
Multi-Probe Assemblies ...................................................... 5 
Phasing Probes................................................................... 5 
SD-6 Short Driveway Dual-Probe System .......................... 5 
Connecting Other Sensing Devices to Control Unit ............ 6 
Installing Sounders (Annunciators) ..................................... 6 
Field Troubleshooting ......................................................... 7 
Splicing Probe Cable .......................................................... 8 
Warranty Information .......................................................... 9 
Merchandise Return Information ......................................... 9 
Technical Specifications ..................................................... 9 

www.GateOpenerSafety.com  |  (800) 878-7829  |  [email protected]

Содержание DRIVEGUARD












Отзывы: