manualshive.com logo in svg

Carrier WeatherMaker 48TC A/B07 Series, Руководство по установке

Поделиться
Скачать
Carrier WeatherMaker 48TC A/B07 Series Скачать руководство пользователя страница 38

38

HUMIDI-MIZER

®

 CONTROL CONNECTIONS

Humidi-MiZer – Space RH Controller

NOTE: The Humidi-MiZer is a factory installed option.

The  Humidi-MiZer  dehumidification  system  requires  a  field-

supplied and field-installed space relative humidity control de

-

vice. This device may be a separate humidistat control (contact

closes on rise in space RH above control set point) or a combina

-

tion  thermostat-humidistat  control  device  such  as  Carrier’s

Edge® Pro Thermidistat with isolated contact set for dehumidi

-

fication control (see Fig. 67 and 68). The humidistat is normally

used in applications where a temperature control is already pro

-

vided (units with PremierLink™ control).

To Connect the Carrier Humidistat (HL38MG029) for 

Sizes 07-14:

1. Route  the  humidistat  2-conductor  cable  (field-supplied)

through the hole provided in the unit corner post.

2. Feed wires through the raceway built into the corner post

(see Fig. 63) to the 24-v barrier located on the left side of

the  control  box.  The  raceway  provides  the  UL-required

clearance between high-voltage and low-voltage wiring.

3. Use wire  nuts  to  connect  humidistat cable  to  two  PINK

leads in the low-voltage wiring as shown in Fig. 69.

To Connect the Carrier Humidistat (HL38MG029) for 

Sizes 16:

1. Route  the  humidistat  2-conductor  cable  (field-supplied)

through the bushing the unit’s louvered end panel.

2. Route the cable through the snap-in wire tie and up to the

web bushing near the control box.

3. Feed the  cable through the  bushing and  into the  bottom

left side of the control box after removing one of the two

knockouts in the corner of the box. Use a connector to pro

-

tect the cable as it enters the control box.

4. Use the connector and the wire tie to reduce any slack in

the humidistat cable to ensure that it will not be damaged

by contact with the condenser coil.

5. Use wire  nuts  to  connect  humidistat cable  to  two  PINK

leads in the low-voltage wiring as shown in Fig. 70.

To connect the Thermidistat device (33CS2PPRH-01) for 

Size 07-14:

1. Route the Thermidistat multi-conductor thermostat cable

(field-supplied) through the hole provided in the unit cor

-

ner post.

2. Feed wires through the raceway built into the corner post

(see Fig. 63) to the 24-v barrier located on the left side of

the  control  box.  The  raceway  provides  the  UL-required

clearance between high-voltage and low-voltage wiring.

3. The Thermidistat has dry contacts at terminals D1 and D2

for dehumidification operation (see Fig. 71). The dry con

-

tacts must be wired between CTB terminal R and the PINK

lead  to  the  LTLO  switch  with  field-supplied  wire  nuts.

Refer to the installation instructions included with the Car

-

rier Edge Thermidistat device for more information.

To connect the Thermidistat device (33CS2PPRH-01) for 

Size 16:

1. Route the Thermidistat multi-conductor thermostat cable

(field-supplied)  through  the  bushing  the  unit’s  louvered

end panel.

2. Route the cable through the snap-in wire tie and up to the

web bushing near the control box.

3. Feed the  cable through the  bushing and  into the  bottom

left side of the control box after removing one of the two

knockouts in the corner of the box. Use a connector to pro

-

tect the cable as it enters the control box.

4. Use the connector and the wire tie to reduce any slack in

the thermostat cable to ensure that it will not be damaged

by contact with the condenser coil.

5. The Thermidistat has dry contacts at terminals D1 and D2

for dehumidification operation (see Fig. 71). The dry con

-

tacts must be wired between CTB terminal R and the PINK

lead  to  the  LTLO  switch  with  field-supplied  wire  nuts.

Refer to the installation instructions included with the Car

-

rier Edge Thermidistat device for more information.

Fig. 67 — 

Accessory Field-Installed Humidistat

Fig. 68 — 

Edge

®

 Pro Thermidistat

Low Ambient Control (Factory Option)

If the unit comes with Electro-Mechanical (EM) control, then no

adjustment is necessary. If the unit comes with PremierLink

™

 or

RTU  Open  control  option,  then  refer  to  its  installation  control

manual for details on adjusting “Cooling Lock-Out” setting and

configure for your specific job requirements.

% RELATIVE HUMIDITY

®

Содержание WeatherMaker 48TC A/B07 Series





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды