Carrier WeatherMaker 48TC A/B07 Series Скачать руководство пользователя страница 32

Страница: 32 / 60

Fig. 50 —

Mounting Position for Field Disconnects

(over 100A) (Size 16)

Fig. 51 —

Mounting Position for Field Disconnects

(up to 100A) (Size 16)

ALL UNITS
Field power wires are connected to the unit at line-side pressure

lugs on compressor contactor C and indoor fan contactor IFC (see

wiring diagram label for control box component arrangement) or

at factory-installed option non-fused disconnect switch. Max wire

size is #4 AWG (copper only) (sizes 07-14) and #2 AWG (copper

only) (size 16). See Fig. 46 and 47.

Refer to Table 7 for maximum wire size at connection lugs. Use

copper wire only. See Fig. 46, 47, and 52.

Table 7 —

Connection Lug Min/Max Wire Sizes

NOTE: TEST LEADS - Unit may be equipped with short leads

(pigtails) on the field line connection points on contactor C or op

tional disconnect switch, see Fig. 46 and 47. These leads are for

factory run-test purposes only; remove and discard before con

necting field power wires to unit connection points. Make field

power connections directly to line connection pressure lugs only.

Fig. 52 —

Disconnect Switch and Unit

UNITS WITH FACTORY-INSTALLED NON-FUSED DIS

CONNECT
The factory-installed optional non-fused disconnect (NFD) switch

is located in a weatherproof enclosure located under the main con

trol box. The manual switch handle and shaft are shipped in the

disconnect enclosure. Assemble the shaft and handle to the switch

at this point. Discard the factory test leads (see Fig. 53 and 54).

Connect field power supply conductors to LINE side terminals

when the switch enclosure cover is removed to attach the handle.

Fig. 53 —

Location of Non-Fused Disconnect

Enclosure (Sizes 07-14)

Minimum

Maximum

TB1 In Unit Control Box

#14

80A Disconnect Option

#14

100A Disconnect Option

1/0

WARNING

FIRE HAZARD

Failure to follow this warning could result in personal injury,

death, or property damage.

Do not connect aluminum wire between disconnect switch and

unit. Use only copper wire.

COPPER

WIRE ONLY

ELECTRIC

DISCONNECT

SWITCH

ALUMINUM

WIRE

Содержание WeatherMaker 48TC A/B07 Series





























































Результаты поиска

Содержание WeatherMaker 48TC A/B07 Series

Отзывы:

Бренды по названию

Популярные бренды

Carrier WeatherMaker 48TC A/B07 Series, Руководство по установке

Результаты поиска

Содержание WeatherMaker 48TC A/B07 Series

Отзывы:

Бренды по названию

Популярные бренды