Carrier WeatherMaker 48TC A/B07 Series Скачать руководство пользователя страница 26

Страница: 26 / 60

(hood divider). Push the filter into position past the open fil

ter clips. Close the filter clips to lock the filter into place. See

Fig. 29.

6. Caulk the ends of the joint between the unit top panel and the

hood top.

7. Replace the filter access panel.

Fig. 27 —

Indoor Coil Access Panel Relocation

(Size 16 Shown)

Fig. 28 —

Economizer Hood Construction

(Size 16 Shown)

Fig. 29 —

Economizer Filter Installation

(Size 16 Shown)

Step 9 —

Install Flue Hood

Flue hood is shipped screwed to the basepan beside the burner

compartment access panel. Remove from shipping location and

using screws provided, install flue hood and screen in location

shown in Fig. 30 for sizes 07-14 and Fig. 31 for size 16.

Fig. 30 —

Flue Hood Details (Sizes 07-14)

Fig. 31 —

Flue Hood Details (Size 16)

Step 10 —

Install Gas Piping

Installation of the gas piping must be accordance with local build

ing codes and with applicable national codes. In U.S.A., refer to

NFPA 54/ANSI Z223.1 National Fuel Gas Code (NFGC). In Can

ada, installation must be in accordance with the CAN/CSA

B149.1 and CAN/CSA B149.2 installation codes for gas-burning

appliances. This unit is factory equipped for use with natural gas

(NG) fuel at elevations up to 2000 ft (610 m) above sea level. Unit

may be field converted for operation at elevations above 2000 ft

(610 m) and/or for use with liquefied petroleum (LP) fuel. See ac

cessory kit installation instructions regarding these accessories.

NOTE: Furnace gas input rate on rating plate is for installation up

to 2000 ft (610 m) above sea level. The input rating for altitudes

above 2000 ft (610 m) must be derated by 4% for each 1000 ft

(305 m) above sea level.

NOTE: Installation of this furnace at altitudes above 2000 ft

(610 m) shall be made in accordance with the Listed High Alti

tude Conversion Kit available with this furnace.

NOTE: L'installation de ce générateur de chaleur à des altitudes

supérieures à 2000 pi (610 mm) doit être effectuée conformément

aux instructions accompagnant la trousse de conversion pour

haute altitude fournie avec cet appareil.

SIDE
PANEL

INDOOR
COIL
ACCESS
PANEL

CAULK
HERE

TOP
PANEL

RAIN DEFLECTORS

TOP
PANEL

INDOOR COIL
ACCESS PANEL

SCREW

HOOD DIVIDER

LEFT
HOOD
SIDE

DIVIDER

BAROMETRIC
RELIEF

CLEANABLE
ALUMINUM
FILTER

FILTER

HOOD

FILTER
CLIP

OUTSIDE
AIR

BLOWER
ACCESS
PANEL

FLUE
HOOD

CONTROL BOX
ACCESS PANEL

Содержание WeatherMaker 48TC A/B07 Series





























































Результаты поиска

Содержание WeatherMaker 48TC A/B07 Series

Отзывы:

Бренды по названию

Популярные бренды

Carrier WeatherMaker 48TC A/B07 Series, Руководство по установке

Результаты поиска

Содержание WeatherMaker 48TC A/B07 Series

Отзывы:

Бренды по названию

Популярные бренды