Carrier N92ESN Скачать руководство пользователя

Страница: 4 / 66

N92ESN: Installation, Start-up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

Improper installation, adjustment, alteration, service, maintenance, or

use can cause explosion, fire, electrical shock, or other conditions which

may cause death, personal injury, or property damage. Consult a

qualified installer, service agency, or your distributor or branch for

information or assistance. The qualified installer or agency must use

factory-authorized kits or accessories when modifying this product.

Refer to the individual instructions packaged with the kits or accessories

when installing.
Installing and servicing heating equipment can be hazardous due to gas

and electrical components. Only trained and qualified personnel should

install, repair, or service heating equipment. Untrained personnel can

perform basic maintenance functions such as cleaning and replacing air

filters. All other operations must be performed by trained service

personnel. When working on heating equipment, observe precautions in

literature, on tags, and on labels attached to or shipped with furnace and

other safety precautions that may apply.
These instructions cover minimum requirements and conform to existing

national standards and safety codes. In some instances, these instructions

exceed certain local codes and ordinances, especially those that may not

have kept up with changing residential construction practices. We

require these instructions as a minimum for a safe installation.
Follow all safety codes. Wear safety glasses, protective clothing, and

work gloves. Have a fire extinguisher available. Read these instructions

thoroughly and follow all warnings or cautions included in literature and

attached to the unit.

This is the safety-alert symbol . When you see this symbol on the

furnace and in instructions or manuals, be alert to the potential for

personal injury.
Understand the signal words DANGER, WARNING, and CAUTION.

These words are used with the safety-alert symbol. DANGER identifies

the most serious hazards which will result in severe personal injury or

death. WARNING signifies a hazard which could result in personal

injury or death. CAUTION is used to identify hazards which may result

in minor personal injury or product and property damage. NOTE and

NOTICE are used to highlight suggestions which will result in enhanced

installation, reliability, or operation.

1. Use only with type of gas approved for this furnace. Refer to the

furnace rating plate.

2. Install this furnace only in a location and position as specified in the

“Location” section of these instructions.

3. Provide adequate combustion and ventilation air to the furnace

space as specified in “Air for Combustion and Ventilation” section.

4. Combustion products must be discharged outdoors. Connect this

furnace to an approved vent system only, as specified in the

“Venting” section of these instructions.

5. Never test for gas leaks with an open flame. Use a commercially

available soap solution made specifically for the detection of leaks

to check all connections, as specified in the “Gas Piping” section.

6. Always install furnace to operate within the furnace’s intended

temperature-rise range with a duct system which has an external

static pressure within the allowable range, as specified in the

“Start-Up, Adjustments, and Safety Check” section. See furnace

rating plate.

7. When a furnace is installed so that supply ducts carry air circulated

by the furnace to areas outside the space containing the furnace, the

return air shall also be handled by duct(s) sealed to the furnace

casing and terminating outside the space containing the furnace.

See “Air Ducts” section.

8. A gas-fired furnace for installation in a residential garage must be

installed as specified in the warning box in the “Location” section.

9. The furnace may be used for construction heat provided that the

furnace installation and operation complies with the first

CAUTION in the LOCATION section of these instructions.

10. These Multipoise Gas-Fired Furnaces are CSA design-certified for

use with natural and propane gases (see furnace rating plate) and for

installation in alcoves, attics, basements, closets, utility rooms,

crawlspaces, and garages. The furnace is factory-shipped for use

with natural gas. A CSA (A.G.A. and C.G.A.) listed accessory gas

conversion kit is required to convert furnace for use with propane

gas.

11. See

Table 1

for required clearances to combustible construction.

Table 1 – Minimum Clearances to Combustible Materials for All

Units

12. Maintain a 1-in. (25 mm) clearance from combustible materials to

supply air ductwork for a distance of 36 in. (914 mm) horizontally

from the furnace. See NFPA 90B or local code for further

requirements.

13. These furnaces SHALL NOT be installed directly on carpeting,

combustible tile, or any other combustible material other than wood

flooring. In downflow installations, factory accessory floor base

MUST be used when installed on combustible materials and wood

flooring. Special base is not required when this furnace is installed

on manufacturer’s Coil Assembly or when Coil Box is used. See

Table 1

for clearance to combustible construction information.

WARNING

FIRE HAZARD

Failure to follow this warning could result in personal injury, death, or

property damage.

Solvents, cements and primers are combustible. Keep away from heat,

sparks and open flame. Use only in well-ventilated areas. Avoid

breathing in vapor or allowing contact with skin or eyes.

CAUTION

FURNACE RELIABILITY HAZARD

Failure to follow this caution may result in unit component damage.
Application of this furnace should be indoors with special attention

given to vent sizing and material, gas input rate, air temperature rise,

unit leveling, and unit sizing.

CAUTION

CUT HAZARD

Failure to follow this caution may result in personal injury.
Sheet metal parts may have sharp edges or burrs. Use care and wear

appropriate protective clothing, safety glasses and gloves when

handling parts, and servicing furnaces.

POSITION

CLEARANCE

REAR

FRONT (Combustion air openings in

furnace and in structure)

1 in. (25 mm)

Required for service

24 in. (610 mm)

*. Consult local building codes

All Sides of Supply Plenum

1 in. (25 mm)

Sides

Vent

Top of Furnace

1 in. (25 mm)

Содержание N92ESN



































































Результаты поиска

Содержание N92ESN

Отзывы:

Похожие инструкции для N92ESN

Бренды по названию

Популярные бренды

Carrier N92ESN, Инструкции по установке, запуску, эксплуатации, обслуживанию и техническому обслуживанию

Результаты поиска

Содержание N92ESN

Отзывы:

Похожие инструкции для N92ESN

Бренды по названию

Популярные бренды