Carrier N92ESN Скачать руководство пользователя

Страница: 37 / 66

N92ESN: Installation, Start-up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

A13078A

Fig. 48 – Alberta and Saskatchewan Vent Termination

A93034

Fig. 49 – Combustion Air and Vent Pipe Diameter Transition

Location and Elbow Configuration

Recommended Combustion Air Inlet Moisture Trap

Recommended to prevent moisture from trickling into the furnace

vestibule, a trap can be installed in the intake air pipe near the furnace.

To prevent moisture, connecting a drain line to the trap is recommended

as trace amounts of moisture will evaporate into the intake air stream. If

the combustion air inlet is located near a moisture exhaust duct, or there

are other concerns of excessive moisture being drawn into the

combustion air inlet, it is encouraged to connect a drain line to the trap.
The trap can be constructed from a running tee of the same diameter of

the intake air pipe with

EITHER

a removable cap attached to a 6-inch

long pipe connected to the tee or the External Vent Trap Kit to help

prevent contaminants from entering the furnace. See

Fig. 50

The External Vent Trap Kit accessory may be used as a trap for the

combustion air inlet pipe if a large amount of moisture must be removed.

The drain line may be connected to the same drain as the furnace

condensate and the evaporator coil condensate line

ONLY

if the inlet air

trap drain and the evaporator coil drain empty into an open segment of

pipe above the drain. See

Fig. 12

. When using the External Vent Trap

Kit, refer to those instructions for proper drain connections.
The tee may also be connected to the intake air pipe on the side of the

casing. See

Fig. 50

In any configuration, it will be necessary to add the equivalent length of

the tee (15 feet/5 M) to the Total Equivalent Vent Length of the venting

system.

The measured length of pipe used in a single or 2-pipe termination is

included in the total vent length. Include deductions from the Maximum

Equivalent Vent Length (MEVL) contained in the Venting Tables for

elbows and flexible vent pipe. Factory accessory concentric vent

terminations or pipe lengths and elbows used for “standard” vent

terminations do not require a deduction from the Maximum Equivalent

Vent Length. See vent termination figures associated with

Table 13

NOTICE

OPTIONAL CONFIGURATION FOR COMBUSTION

AIR INLET PIPE

In applications where there is a risk of excessive moisture entering the

combustion air inlet pipe, a moisture trap may be added to the inlet pipe

to help prevent moisture from entering the furnace from the combustion

air inlet pipe. See

Fig. 50

When sizing venting systems, the equivalent length of the optional

moisture trap (15 feet/5 M) must be taken into account.

OPTIONAL TERMINATION
BRACKET FOR 2-PIPE
TERMINATIONS

12-IN. (305 MM)

ABOVE ANTICIPATED

SNOW LEVEL

12 IN. (305 MM) MIN.
SEPARATION BETWEEN
BOTTOM OF COMBUSTION
AIR AND BOTTOM OF VENT.

12 IN. (305 MM) MIN. SEPARATION
BETWEEN BOTTOM OF
COMBUSTION AIR AND
BOTTOM OF VENT.

MAINTAIN 12 IN. (305 MM)
CLEARANCE ABOVE
HIGHEST ANTICIPATED
SNOW LEVEL OR GRADE,
WHICHEVER IS GREATER.

COMBUSTION-AIR

(ELBOW PARALLEL TO WALL)

OPTIONAL
BRACKET
COUPLING

OVERHANG

12 IN. (305 MM) MIN. GROUND
LEVEL OR ANTICIPATED SNOW LEVEL

EXHAUST

CLEARANCE TO OVERHANG PER CODE

NOTICE

ADDITIONAL INFORMATION FOR POLYPROPYLENE

VENTING SYSTEMS

Polypropylene venting systems include flexible vent pipe. These

flexible vent pipes have a different equivalent vent length than straight

sections of PVC/ABS DWV vent pipe. Be sure to make the appropriate

deductions from the Maximum Equivalent Vent Length (MEVL), or

additions to the Total Equivalent Vent Length (TEVL), when applying

flexible vent pipes in polypropylene venting systems. See the

polypropylene vent system manufacturer’s installation instructions for

details.

When using metric-sized venting systems, use these equivalencies for

obtaining the proper MEVL from the Tables:

Use 2” Vent Tables for 60 mm (o.d.) vent systems

Use 3” Vent Tables for 80 mm (o.d.) vent systems

Use 4” Vent Tables for 100 mm (o.d.) vent systems

FURNACE

PIPE DIAMETER

TRANSITION IN

VERTICAL SECTION

NOT IN
HORIZONTAL
SECTION

Содержание N92ESN



































































Результаты поиска

Содержание N92ESN

Отзывы:

Похожие инструкции для N92ESN

Бренды по названию

Популярные бренды

Carrier N92ESN, Инструкции по установке, запуску, эксплуатации, обслуживанию и техническому обслуживанию

Результаты поиска

Содержание N92ESN

Отзывы:

Похожие инструкции для N92ESN

Бренды по названию

Популярные бренды