background image

Hearth Technologies Inc.

20802 Kensington Blvd.

Lakeville, MN 55044

R-CAST

CENTENNIAL

OWNER’S MANUAL 

AND INSTALLATION INSTRUCTIONS

This manual must be used for installation of the
R-CAST, R-CAST-A, and R-CAST-G Gas-Fired
Wall Furnace and retained by the homeowner for
operating and maintenance instructions.

WARNING!

Improper installation, adjustment, alteration,

service or maintenance can cause injury or

property damage.  Refer to this manual.  For

assistance or additional information, consult

a qualified installer, service agency or the

gas supplier.

This wall furnace may be installed with a vertical

or horizontal direct vent termination system.

FOR YOUR SAFETY:

The appliance area must be kept clear and free from combustible

materials, gasoline and other flammable vapors and liquids.

-Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.

-WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance.

Do not touch any electrical switch; do not use any
phone in your building.

Immediately call your gas supplier from a neigh-
bor’s phone.  Follow the gas supplier’s instruc-
tions.

If you cannot reach your gas supplier, call the fire
department.

-Installation and service must be performed by a
qualified installer, service agency or the gas supplier.

WARNING!

If the information in this manual is not fol-

lowed exactly, a fire or explosion may result

causing property damage, personal injury or

loss of life.

Summary of Contents for R-CAST



























Reviews: