background image

10                                                                 

Specifications subject to change without notice.                                                                         IM-KSAIC03-03

TXV REPLACEMENT PROCESS FOR 
PIPING ADAPTER FOR FV4CNF002L00 AND 
FV4CN(B,F)003L

1. Gain access to the built-in TXV inside the fan coil cabinet.
2. Double-wrench the TXV mechanical connector and disassemble.
3. Cut the bleed line from the TXV to the suction line and braze closed

the capillary tube.

4. Remove the tail bulb from the suction line by cutting the stainless

steel band.

5. Assemble the line set to the piping adapter kit (40MD000003). 

Obtain through RCD. 

a. Refer to “APPENDIX 2 - PIPING ADAPTER BUSHINGS/

REDUCERS” on page 16 for Bushing/Reducer sizing.

b. Adapt (where needed) and braze the liquid line to the piping

adapter. 

6. Place the Teflon gasket on the brass tip of the Piping Adapter and

insert into the aluminum distributor head.

Thread the piping adapter brass nut onto the distributor line and tighten - finger tight + 1/2 turn.

Fig. 14 — Piping Adapter Replacement

BASIC SETUP FOR THE FV4C “EASY SELECT” PRINTED-CIRCUIT BOARD

BASIC FAN COIL CONFIGURATION

The following basic fan coil configuration provides AHRI rated

performance of the heat pump:

A. AUX HEAT KW/CFM 

Select the heater range for the size electric heater installed.

B. AC/HP SIZE 

Select system size installed 
For size 12K, select 018 on the board.
For sizes 18K - 36 K, select the nominal connector on the 

board.

C. SYSTEM TYPE - 

Select system type

D. AC/HP CFM ADJUST 

 

Select NOM

E. ON/OFF DELAY 

 

Select 0/90 profile

F. CONTINUOUS FAN 

 

Select the desired fan speed when the thermostat is set to 

continuous fan. 
For size 12K, select “MED”

Fig. 15 — Detail of FV4C Printed-Circuit Board

Содержание KSAIC0301230

















Отзывы: