Carrier AQUASNAP JUNIOR 30RA015 Скачать руководство пользователя страница 36

Страница: 36 / 48

Typical control wiring schematic (30RA035-055)

NOTES:

FACTORY WIRING IS IN ACCORDANCE WITH NATIONAL ELECTRICAL CODE (NEC). FIELD MODIFICA-

TIONS OR ADDITIONS MUST BE IN COMPLIANCE WITH ALL APPLICABLE CODES.

WIRING FOR MAIN FIELD SUPPLY MUST BE RATED 75C MINIMUM. USE COPPER FOR ALL UNITS. MAXI-

MUM INCOMING WIRE SIZE FOR THE TERMINAL BLOCK IS 350 KCMIL. MAXIMUM INCOMING WIRE SIZE

FOR 100 AMP NON-FUSED DISCONNECT IS #1 AWG. MAXIMUM INCOMING WIRE SIZE FOR 250 AMP

NON-FUSED DISCONNECT IS 350 KCMIL.

TERMINALS 9 AND 10 OF TB5 ARE FOR FIELD EXTERNAL CONNECTIONS FOR REMOTE ON-OFF. THE

CONTACTS MUST BE RATED FOR DRY CIRCUIT APPLICATION CAPABLE OF HANDLING A 24 VAC LOAD

UP TO 50 MA.

TERMINALS 1 AND 2 OF TB5 ARE CONNECTED TO THE FACTORY INSTALLED CHILLED WATER FLOW

SWITCH (CWFS). TO ADD CHILLED WATER PUMP INTERLOCK CONTACTS, REMOVE THE ORANGE HAR-

NESS WIRE FROM TB5-1 AND WIRE CONTACTS IN SERIES AS SHOWN. THE CONTACTS MUST BE RATED

FOR DRY CIRCUIT APPLICATION CAPABLE OF HANDLING A 24VAC LOAD UP TO 50 MA.

TERMINALS 11 AND 13 OF TB5 ARE FOR CONTROL OF CHILLED WATER PUMP 1 (CWP1) STARTER. TER-

MINALS 13 AND 15 OF TB5 ARE FOR CONTROL OF CHILLED WATER PUMP 2 (CWP2) STARTER. THE MAX-

IMUM LOAD ALLOWED FOR THE CHILLED WATER PUMP RELAY IS 5 VA SEALED, 10 VA INRUSH AT 24 V.

FIELD POWER SUPPLY IS NOT REQUIRED.

TERMINALS 12 AND 13 OF TB5 ARE FOR AN ALARM RELAY. THE MAXIMUM LOAD ALLOWED FOR THE

ALARM RELAY IS 5 VA SEALED, 10 VA INRUSH AT 24 V. FIELD POWER SUPPLY IS NOT REQUIRED.

MAKE APPROPPRIATE CONNECTIONS TO TB6 AS SHOWN FOR ENERGY MANAGEMENT BOARD

OPTIONS. THE CONTACTS FOR DEMAND LIMIT AND ICE DONE OPTIONS MUST BE RATED FOR DRY CIR-

CUIT APPLICATION CAPABLE OF HANDLING A 24VAC LOAD UP TO 50MA.

LEGEND

—

Alarm

AWG

—

American Wire Gage

CWP

—

Chilled Water Pump

CWPI

—

Chilled Water Pump Interlock

EMM

—

Energy Management Module

GFI-CO

—

Ground Fault Interrupt Convenience Outlet

FIOP

—

Factory-Installed Option

NEC

—

National Electric Code

SPT

—

Space Temperature

—

Terminal Block

a30-4607

Содержание AQUASNAP JUNIOR 30RA015

















































Результаты поиска

Содержание AQUASNAP JUNIOR 30RA015

Отзывы:

Carrier AQUASNAP JUNIOR 30RA015, Данные о продукции, Страница: 36 / 48

Результаты поиска

Содержание AQUASNAP JUNIOR 30RA015

Отзывы: