Carrier AQUASNAP JUNIOR 30RA015 Скачать руководство пользователя страница 28

Страница: 28 / 48

Typical piping and wiring

AIR FLOW

FIELD
POWER
SUPPLY

DRAIN

FLOW

GATE
VALVE

VIBRATION
ELIMINATOR

VALVE
PRESSURE
GAGE

SHUT OFF
VALVES

HEAT TAPE INSULATION IS RECOMMENDED ON ALL EXPOSED PIPING
IF AMBIENT TEMPERATURE <32 F (0

C) AND NO ANTIFREEZE SOLUTION IS IN SYSTEM

CONTROL
WIRING

EXPANSION

TANK

PUMP

AIR FLOW

FIELD
POWER
SUPPLY

DRAIN

FLOW

GATE
VALVE

VIBRATION
ELIMINATOR

NOTE 5

HEAT TAPE INSULATION IS RECOMMENDED ON ALL EXPOSED PIPING
IF AMBIENT TEMPERATURE <32 F (0

C) AND NO ANTIFREEZE SOLUTION IS IN SYSTEM

CONTROL
WIRING

30RA UNITS WITHOUT HYDRONIC PACKAGE

30RA UNITS WITH HYDRONIC PACKAGE

NOTES:
1. Chiller must

e installed level to within

in. per foot (10.4 mm per meter) to maintain proper compressor oil return and hydraulics.

2. Wiring and piping shown are general points-of-connection guides only and are not intended for a specific installation. Wiring and piping shown are

for a quick overview of system and are not in accordance with recognized standards.

3. All wiring must comply with applica

le local and national codes.

4. All piping must follow standard piping techniques. Refer to Carrier System Design Manual or appropriate ASHRAE (American Society of Heating,

Refrigeration, and Air Conditioning Engineers) hand

ook for details.

LEGEND

Airflow Through Condenser

Power Wiring

Chilled Water Piping

LEGEND

Airflow Through Condenser

Power Wiring

Chilled Water Piping

NOTES:
1. Chiller must

e installed level to within

in. per foot (10.4 mm per meter) to maintain proper compressor oil return and hydraulics.

2. Wiring and piping shown are general points-of-connection guides only and are not intended for a specific installation. Wiring and piping shown are for a

quick overview of system and are not in accordance with recognized standards.

3. All wiring must comply with applica

le local and national codes.

4. All piping must follow standard piping techniques. Refer to Carrier System Design Manual or appropriate ASHRAE (American Society of Heating,

Refrigeration, and Air Conditioning Engineers) hand

ook for details.

5. Air separator required as close to chiller as possi

le (except primary/secondary systems).

Содержание AQUASNAP JUNIOR 30RA015

















































Результаты поиска

Содержание AQUASNAP JUNIOR 30RA015

Отзывы:

Carrier AQUASNAP JUNIOR 30RA015, Данные о продукции, Страница: 28 / 48

Результаты поиска

Содержание AQUASNAP JUNIOR 30RA015

Отзывы: