Carrier AquaSnap 61AF 022 Скачать руководство пользователя

Страница: 6 / 44

Operating checks:
Important information regarding the refrigerant used:
This product contains fluorinated greenhouse gas covered

by the Kyoto protocol.
Fluid type: R407C
Global Warming Potential (GWP): 1774
CAUTION: :
1. Any intervention on the refrigerant circuit of this product

should be performed in accordance with the applicable

legislation. In the EU, the regulation is called F-Gas,

N°517/2014.

2. Ensure that the refrigerant is never released to the

atmosphere during installation, maintenance or equipment

disposal.

3. The deliberate gas release into the atmosphere is not

allowed.

4. If a refrigerant leak is detected, ensure that it is stopped

and repaired as quickly as possible.

5. Only a qualified and certified personnel can perform

installation operations, maintenance, refrigerant circuit

leak test as well as the equipment disposal and the

refrigerant recovering.

6. The gas recovery for recycling, regeneration or destruction

is at customer charge.

7. Periodic leak tests have to be carried out by the customer

or by third parties. The EU regulation set the periodicity

here after:

System WITHOUT

leakage detection

No Check 12 Months 6 Months 3 Months

System WITH

leakage detection

No Check 24 Months 12 Months 6 Months

Refrigerant charge/

circuit (CO

equivalent)

< 5 Tons

5 ≤ charge

< 50 Tons

50 ≤

charge <

500 Tons

Charge >

500

Tons

(1)

Refrigerant

charge/

Circuit (kg)

R134A

(GWP

1430)

Charge <

3,5 kg

3,5 ≤

charge <

34,9 kg

34,9 ≤

charge <

349,7 kg

Charge >

349,7 kg

R407C

(GWP

1774)

Charge <

2,8 kg

2,8 ≤

charge <

28,2 kg

28,2 ≤

charge <

281,9 kg

Charge >

281,9 kg

R410A

(GWP

2088)

Charge <

2,4 kg

2,4 ≤

charge <

23,9 kg

23,9 ≤

charge <

239,5 kg

charge >

239,5 kg

HFO’s :

R1234ze

No requirement

(1) From 01/01/2017, units must be equipped with a leakage detection system

8. A logbook must be established for equipments subject to

periodic leak tests. It should contain the quantity and the

type of fluid present within the installation (added and

recovered), the quantity of recycled fluid, regenerated or

destroyed, the date and output of the leak test, the

designation of the operator and its belonging company,

etc.

9. Contact your local dealer or installer if you have any

questions.

Protection device checks:

- If no national regulations exist, check the protection

devices on site in accordance with standard EN378: once

a year for the high-pressure switches, every five years for

external relief valve.

The company or organisation that conducts a pressure switch test

shall establish and implement a detailed procedure to fix :

Safety measures

Measuring equipment calibration

Validating operation of protective devices

Test protocols

Recommissioning of the equipment..

Consult Carrier Service for this type of test. Carrier mentions here

only the principle of a test without removing the pressure switch:

Verify and and record the set-points of pressure switches

and relief devices (valves and possible rupture discs)

Be ready to switch-off the main disconnect switch of the power

supply if the pressure switch does not trigger (avoid

overpressure or excess gas in case of valves on the high-

pressure side with the recovery condensers)

Connect a pressure gauge protected against pulsations (filled

with oil with maximum pointer if mechanical), preferably

calibrated (the values displayed on the user interface may

be inaccurate in an instant reading because of the scanning

delay applied in the control)

Complete an HP Test as provided by the software (refer to

the Control IOM for details).

If the machine operates in a corrosive environment, inspect

the protection devices more frequently. Regularly carry out

leak tests and immediately repair any leaks.
Ensure regularly that the vibration levels remain acceptable

and close to those at the initial unit start-up. Before opening

a refrigerant circuit, transfer the refrigerant to bottles

specifically provided for this purpose and consult the

pressure gauges.
Change the refrigerant after an equipment failure, following

a procedure such as the one described in NF E29-795 or carry

out a refrigerant analysis in a specialist laboratory.
If the refrigerant circuit remains open for longer than a day

after an intervention (such as a component replacement), the

openings must be plugged and the circuit must be charged

with nitrogen (inertia principle). The objective is to prevent

penetration of atmospheric humidity and the corrosion on

the unprotected internal steel walls.

1 - INTRODUCTION

Содержание AquaSnap 61AF 022













































Результаты поиска

Содержание AquaSnap 61AF 022

Отзывы:

Похожие инструкции для AquaSnap 61AF 022

Бренды по названию

Популярные бренды

Carrier AquaSnap 61AF 022, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание AquaSnap 61AF 022

Отзывы:

Похожие инструкции для AquaSnap 61AF 022

Бренды по названию

Популярные бренды