Carrier AquaSnap 61AF 022 Скачать руководство пользователя страница 36

Страница: 36 / 44

14 - HEATING SYSTEM MANAGER (HSM)

14.1 - Accessory 00PPG000488000- Heating System Managere type A

Heating system control (as accessory 00PPG000488000) two

heat emitter types or independent zones and domestic hot

water production

Allows control of a non-reversible heating system that includes a

61AF heat pump and two different heat emitter types and/or two

independent comfort zones. For optimised energy efficiency the heat

pump is controlled by a configurable weather compensation system.

The control box controls a supplementary electric heater or a

stand-by boiler. The control box supplies power to the circulating

pumps. Hot-water production can be permanent or programmable

with a second setpoint at the heat pump and control of a switching

valve.

Heating system example: one heat emitter type with supplementary electric heating or stand-by boiler

Legend

GT1

Water temperature loop 1

GT3

Outdoor air temperature

Pump for water loop 1 (radiators)

External water pump for the heat pump

SV31

Three-way mixing valve for the back-up heater

Hot water

Back-up system

Heating system

61AF + HSM

GT1 SV31

GT...
P1...

SV...

GT3

14.2 - Accessory 00PPG000488100- Heating System Manager type B

Heating system control (as accessory 00PPG000488000) two

heat emitter types or independent zones and domestic hot

water production:

Allows control of a non-reversible heating system that includes a

61AF heat pump and two different heat emitter types and/or two

independent comfort zones. For optimised energy efficiency the

heat pump is controlled by a configurable weather compensation

system.

The control box controls a supplementary electric heater or a

stand-by boiler. The control box supplies power to the circulating

pumps. Hot-water production can be permanent or programmable

with a second setpoint at the heat pump and control of a switching

valve

Heating system example: two heat emitter types or independent zones and domestic hot water production

P7-2

GT1

GT4

SV34

SV31

GT5

SV35

GT7

GT2

GT7:2

SV32

GT..
P..

SV..

Back-up system

Heating system

Floor heating

Domestic hot

water in

61AF + HSM

Hot water

GT3

Legend
Thermistors

GT1

Water temperature loop 1

GT2

Domestic hot water tank temperature

GT3

Outdoor air temperature

GT4

Water temperature loop 2

GT5

Domestic hot water temperature

GT7

Additional domestic hot water tank t

emperature

Pumps

Pump for water loop 1 (radiators)

External water pump for the heat pump

Pump for water loop 2 (floor heating)

Pump to pre-heat the domestic hot water valve loop

Pump for domestic hot water circulation

P7-2

Pump for domestic hot water circulation in an aditional

tank

Valves

SV31

Three-way mixing valve for the back-up heater

SV32

Heating/domestic hot water change-over valve

SV34

Three-way control valve for water loop 2

SV35

Three-way mixing valve for domestic hot water

NOTES: :

This application example includes two zones and a supplementary boiler and domestic hot-water production.

The installation includes a switching valve (SV32) that allows switching from the heat pump capacity of the heating system to

domestic hot-water production.

The primary heating circuit is the domestic hot-water production circuit. It includes a tank with an equivalent pressure drop to

simplify system balancing.

Содержание AquaSnap 61AF 022













































Результаты поиска

Содержание AquaSnap 61AF 022

Отзывы:

Carrier AquaSnap 61AF 022, Инструкции по установке, эксплуатации и обслуживанию, Страница: 36 / 44

Результаты поиска

Содержание AquaSnap 61AF 022

Отзывы: