manualshive.com logo in svg

Carrier AquaForce 30XAV 1050, Инструкции по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Carrier AquaForce 30XAV 1050 Скачать руководство пользователя страница 21

21

6.4 - Variable flow evaporator

Variable evaporator flow can be used as standard with 
30XAV chillers. The chillers maintain a constant leaving water 

temperature under all flow conditions. For this to happen, 
the flow rate must be higher than the minimum flow given 
in the table of permissible flow rates and must not vary by 

more than 10% per minute.

If  the  flow  rate  changes  more  rapidly,  the  system  should 

contain a minimum of 6.5 litres of water per kW instead of 
3.25 l/kW.

The flow can also be controlled by the unit through option 

299 : Variable Water Flow Control. This option allows the 
unit to control an external pump in order to maintain a 
constant inlet/outlet temperature difference, a constant outlet 
pressure or an unoccupied mode.

6.5 - System minimum water volume

Whichever the system, the water loop minimum capacity is 
given by the formula:

Capacity = Cap (kW) x N litres

Application

N

Normal air conditioning

3.25

Process type cooling

6.5

Where Cap is the nominal system cooling capacity (kW) at 
the nominal operating conditions of the installation.

This volume is necessary for stable operation and accurate 
temperature control.

It is often necessary to add a buffer water tank to the circuit 
in order to achieve the required volume. The tank must itself 

be internally baffled in order to ensure proper mixing of the 

liquid (water or brine). Refer to the examples below.

Connection to a buffer tank

Bad

Good

Bad

Good

6.6 - Evaporator water flow rate

30XAV

Evaporator water flow rate, l/s*

Dual pass

Single pass

Minimum

Maximum

Minimum

Maximum

500

7.1

51.5

17

57.6

600

8.9

63.1

21

69.1

700

8.9

63.1

21

80.6

800

11.2

73.1

25.5

92.1

950

12.4

82.2

28.3

109.4

1050

13.1

93.9

31.1

120.9

1150

15.4

95.5

34.2

132.5

* 

Standard evaporator and coolant 

=

 water

6.7 -  Evaporator pressure drop curve

Water flow rate, L/s

Pr

essur

e dr

op

, kP

a

500

600-700

800

950

1050

1150

0

10

20

30

40

10

20

30

40

50

60

70

80

90

100

110

120

130

Pre

ss

ure

 d

ro

p,

 k

Pa

Water flow rate, L/s

One pass Evaporator pressure drop curves (option 100C)

 

3

Legend:

1 500

2 600

3 

700

4 

800

5 

950

6 1050

7 

1150

 

4

 

5

 

6

 

7

Note: 

Standard evaporator and coolant = water

Sizes 500 to 1150

Содержание AquaForce 30XAV 1050











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды