Carrier AIRSTREAM 42BHE Скачать руководство пользователя страница 2

2

See drawings for unit configurations, dimensions, clearanc-

es, and pipe connections. Refer to unit wiring label for all elec-

trical connections. Follow NEC (National Electrical Code) and

local codes.

INSTALLATION

Step 1 — Unpack and Inspect Unit — 

Remove ship-

ping wraps from unit and check shipment against shipping list.

Check for concealed shipping damage. If shipment is damaged

or incomplete, file claim with transportation company and

contact your local Carrier representative immediately.

Step 2 — Protect Unit from Damage — 

To main-

tain warranty, protect unit against adverse weather conditions,

theft or vandalism on the jobsite.

The described equipment 

IS NOT

 suitable for outdoor in-

stallations. The equipment should never be stored or installed

where it may be subjected to a hostile environment such as

rain, snow, or extreme temperatures.

Step 3 — Prepare Jobsite — 

To save time and to re-

duce the possibility of costly errors, set up a complete sample

installation in a typical room at jobsite. Check all critical di-

mensions such as pipe, wire and duct connection requirements.

Refer to job drawings and product dimension drawings as re-

quired. Instruct all trades in the appropriate part of the installa-

tion. For unit component identification, refer to Fig. 1.  For unit

dimensions, refer to Fig. 2 for 42BHE units and Fig. 3 for

42BVE units.

NOTES:

1. All dimensions are in inches (±

1

/

4

 in.).

2. Any modifications to product specifications by any person are subject to acceptance of the factory. Product specifications are subject to change without notice.
3. Right hand shown, left hand opposite.
4. Hanger rods, which are field supplied, are shown for reference only.

UNIT

42BHE

DIMENSIONS (in.)

Fan Size

Depth

Width

Height

Supply Duct

Return Duct

Mounting Holes

A

B

C

D

E

F

J

K

06

9 x  4

36

28

19

3

/

4

7

1

/

8

10

1

/

2

14

1

/

2

2

1

/

4

24

16

1

/

2

27

1

/

4

35

1

/

4

08

9 x  6

36

28

19

3

/

4

8

1

/

2

10

1

/

2

13

7

/

8

2

1

/

4

24

16

1

/

2

27

1

/

4

35

1

/

4

10

10 x  4

37

1

/

2

37

21

1

/

2

7

1

/

8

11

9

/

16

15

1

/

4

2

1

/

4

33

18

1

/

4

36

1

/

4

37

12

10 x  7

37

1

/

2

37

21

1

/

2

9

15

/

16

11

9

/

16

13

7

/

8

2

1

/

4

33

18

1

/

4

36

1

/

4

37

16

11 x 10

37

3

/

4

47

21

1

/

2

13

3

/

8

12

3

/

4

16

3

/

4

2

1

/

4

43

18

1

/

4

46

1

/

4

37

20

12 x  9

40

1

/

4

48

24

12

1

/

2

13

3

/

4

17

3

/

4

2

1

/

4

44

20

3

/

4

47

1

/

4

39

1

/

2

30

12 x 12

40

1

/

4

48

32

1

/

4

15

7

/

8

13

3

/

4

16

7

1

/

4

44

29

47

1

/

4

39

1

/

2

40

15 x 12

43

1

/

2

62

32

1

/

4

16

7

/

16

16

1

/

16

22

3

/

4

6

1

/

4

58

29

61

3

/

4

42

1

/

2

Fig. 2 — Unit Dimensions — 42BHE Units

A42-659ef

Содержание AIRSTREAM 42BHE













Отзывы: