manualshive.com logo in svg

Carrier 58MSA Series, Инструкция по установке, запуску и эксплуатации

Поделиться
Скачать
Carrier 58MSA Series Скачать руководство пользователя страница 37

a. Remove burner enclosure front.

b. Remove cap that conceals adjustment screw for gas valve

regulator. (See Fig. 46.)

c. Jumper R and W thermostat connections on control to start

furnace operation.

d. Turn adjusting screw, counterclockwise (out) to decrease

manifold pressure or clockwise (in) to increase manifold
pressure.

NOTE:

This furnace has been approved for a manifold pressure

of 3.2 in. wc to 3.8 in. wc when installed at altitudes up to 2000 ft.
For altitudes above 2000 ft, the manifold pressure can be adjusted
from 2.0 in. wc to 3.8 in. wc. If manifold pressure is outside this
range, change burner orifices to obtain pressure in this range.

DO NOT bottom out gas valve regulator adjusting screw.
This can result in unregulated manifold pressure and result in
excess overfire and heat exchanger failures.

NOTE:

If orifice hole appears damaged or it is suspected to have

been redrilled, check orifice hole with a numbered drill bit of
correct size. Never redrill an orifice. A burr-free and squarely
aligned orifice hole is essential for proper flame characteristics.

e. Replace gas valve regulator adjustment screw cap.

f. Replace burner enclosure front and verify adjusted gas

input rate using method outlined in item 3.

DO NOT redrill orifices. Improper drilling (burrs, out-of-
round holes, etc.) can cause excessive burner noise and
misdirection of burner flames. This can result in flame
impingement of burners and heat exchangers causing failures.
(See Fig. 47.)

g. Look through sight glass in burner enclosure and check

burner flame. Burner flame should be clear blue, almost
transparent. (See Fig. 48.)

h. Remove jumper from R and W.

3. Verify natural gas input rate by clocking gas meter.

Fig. 44—Inducer Housing Drain Cap

A99118

Fig. 45—Filling Condensate Trap

A99119

Fig. 46—Redundant Automatic Gas Valve

A03142

REGULATOR 
SEAL CAP

REGULATOR
ADJUSTMENT
SCREW

REGULATOR SPRING
(PROPANE - WHITE, 6 TURNS
NATURAL - SILVER, 10 TURNS)

GAS PRESSURE 
REGULATOR 
ADJUSTMENT

MANIFOLD 
PRESSURE TAP

INLET 
PRESSURE TAP

ON/OFF SWITCH

37

→

Содержание 58MSA Series

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды