Carrier 50SD024, Руководство по установке

Страница: 10 / 22

10
Table 1— Physical Data--Unit 50SD
UNIT SIZE 024 030 036 042 048 060
NOMINAL CAPACITY (ton) 2 2--1/2 3 3--1/2 4 5
OPERATING WEIGHT (lb.) 289 312 371 398 418 430
COMPRESSOR Scroll
REFRIGERANT (R--22) Quantity (lb.) 7.8 8.4 10.9 10.9 12.3 12.0
REFRIGERANT METERING DEVICE AccuRater
®
ORIFICE OD (in.) 0.065 0.070 0.080 0.088 0.088 0.101
OUTDOOR COIL
Rows
…
Fins/in.
2
…
21
2
…
21 2
…
21 2
…
21 2
…
21 2
…
21
Face Area (sq. ft.) 11.9 13.6 15.5 19.4 19.4 19.4
OUTDOOR FAN
Nominal Cfm 2700 2700 2800 2800 3300 3300
Diameter 22 22 22 22 22 22
Motor HP (RPM) 1/8 (825) 1/8 (825) 1/8 (825) 1/8 (825) 1/4 (1100) 1/4 (1100)
INDOOR COIL
Rows
…
Fins/in. 3
…
17 3
…
17 3
…
17 3
…
17 3
…
17 4
…
17
Face Area (sq. ft.) 3.7 3.7 4.7 4.7 5.6 5.6
INDOOR BLOWER
Nominal Airflow (Cfm) 800 1000 1200 1400 1600 1750
Size (in.) 10x10 10x10 11x10 11x10 11x10 11x10
Motor HP (RPM) 1/3 (1050) 1/3 (1050) 1/2 (1000) 1/2 (1075) 1/2 (1075) 1.0 (1040)
RETURN--AIR FILTERS (IN.)*
20x24x1 20x24x1 24x36x1 24x36x1 24x36x1 24x36x1
Throwaway
*Required filter sizes shown are based on the larger of the ARI (Air Conditioning and Refrigeration Institute) rated cooling airflow or the heating airflow velocity
of 300 ft/minute for throwaway type. For permanent filters, follow filter manufacturer’s recommendations for filter size based on allowable face velocity. Air filter
pressure drop for non---standard filters must not exceed 0.08 in. wg.
Table 2—Minimum Airflow for Safe Electric Heater Operation (Cfm)
SIZE 024 030 036 042 048 060
Cfm 800 1000 1200 1400 1600 1750
PRE--START--UP
FIRE, EXPLOSION, ELECTRICAL SHOCK HAZARD
Failure to follow this warning could result in personal injury
or death and/or property damage.
1. Follow recognized safety practices and wear protective
goggles when checking or servicing refrigerant system.
2. Relieve and recover all refrigerant from system before
touching or disturbing anything inside terminal box if
refrigerant leak is suspected around compressor terminals.
3. Never attempt to repair soldered connection while
refrigerant system is under pressure.
4. Do not use torch to remove any component. System
contains oil and refrigerant under pressure.
5. To remove a component, wear protective goggles and
proceed as follows:
a. Shut off electrical power to unit and install lockout
tag.
b. Relieve and reclaim all refrigerant from system
using both high-- and low--pressure ports.
c. Cut component connecting tubing with tubing
cutter and remove component from unit.
d. Carefully unsweat remaining tubing stubs when
necessary. Oil can ignite when exposed to torch
flame.
!
WARNING
Proceed as follows to inspect and prepare the unit for initial start--up:
1. Remove all access panels.
2. Read and follow instructions on all DANGER, WARNING,
CAUTION, and INFORMATION labels attached to, or
shipped with unit.
3. Make the following inspections:
a. Inspect for shipping and handling damages, such as
broken lines, loose parts, disconnected wires, etc.
b. Inspect for oil at all refrigerant tubing connections and on
unit base. Detecting oil generally indicates a refrigerant
leak. Leak test all refrigerant tubing connections using
electronic leak detector, or liquid--soap solution. If a
refrigerant leak is detected, see following Check for
Refrigerant Leaks section.
c. Inspect all field-- and factory--wiring connections. Be
sure that connections are completed and tight.
d. Ensure wires do not touch refrigerant tubing or sharp
sheet metal edges.
e. Inspect coil fins. If damaged during shipping and
handling, carefully straighten fins with a fin comb.
4. Verify the following conditions:
a. Make sure that outdoor fan blade is correctly positioned
in fan orifice (See Fig. 12).
b. Make sure that condensate drain pan and trap are filled
with water to ensure proper drainage.
c. Make sure that all tools and miscellaneous loose parts
have been removed.
FAN GRILLE
MOTOR
1/8" MAX BETWEEN
MOTOR AND FAN HUB
MOTOR SHAFT
1/2ý
C99009
Fig. 12 -- Fan Blade Clearance
START--UP
CHECK FOR REFRIGERANT LEAKS
Proceed as follows to locate and repair a refrigerant leak and to
charge the unit:
50SD