Carrier 48FC 04 Скачать руководство пользователя страница 47

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.

Catalog No. 04-53480245-01

Printed in U.S.A.

Form 48FC-4-7-02SI

Pg CL-1 

2-19

Replaces: 48FC-4-7-01SI

START-UP CHECKLIST FOR 48FC04-07 SINGLE PACKAGE ROOFTOP

GAS HEATING/ELECTRIC COOLING UNIT

(Remove and use for job file)

 

I. PRELIMINARY INFORMATION

MODEL NO ____________________________________________

JOB NAME _____________________________________________

SERIAL NO ____________________________________________

ADDRESS _____________________________________________

START-UP DATE________________________________________

TECHNICIAN NAME _____________________________________

ADDITIONAL ACCESSORIES

_____________________________________________________________________________________________________

II. PRE-START-UP

Verify that all packaging materials have been removed from unit 

(Y/N) _____

Verify installation of outdoor air hood 

(Y/N) _____

Verify installation of flue exhaust and inlet hood 

(Y/N) _____

Verify that condensate connection is installed per instructions   

(Y/N) _____

Verify that all electrical connections and terminals are tight 

(Y/N) _____

Verify gas pressure to unit gas valve is within specified range 

(Y/N) _____

Check gas piping for leaks 

(Y/N) _____

Check that indoor-air filters are clean and in place 

(Y/N) _____

Check that outdoor air inlet screens are in place

(Y/N) _____

Verify that unit is level 

(Y/N) _____

Verify that fan assembly is free of obstructions and rotor spins freely 

(Y/N) _____

Verify that scroll compressors are rotating in the correct direction 

(Y/N) _____

Verify installation of thermostat 

(Y/N) _____

Verify that crankcase heaters have been energized for at least 24 hours  (Y/N) _____

III. START-UP

ELECTRICAL

Supply Voltage 

L1-L2_____________

L2-L3_____________

L3-L1_____________

Compressor Amps 1

L1   _____________

L2   _____________

L3   _____________

Compressor Amps 2

L1   _____________

L2   _____________

L3   _____________

Supply Fan Amps

L1   _____________

L2   _____________

L3   _____________

TEMPERATURES

Outdoor-air Temperature 

_____________ °F DB (Dry Bulb)

Return-air Temperature 

_____________ °F DB 

_____________ 

°

F WB (Wet Bulb) 

Cooling Supply Air Temperature 

_____________ °F

Gas Heat Supply Air 

_____________ °F

NOTE:  To avoid injury to personnel and damage to equipment or

property when completing the procedures listed in this start-up

checklist, use good judgment, follow safe practices, and adhere

to the safety considerations/information as outlined in preced-

ing sections of this Installation Instruction document.

Содержание 48FC 04

















































Отзывы: