Carrier 42DH Скачать руководство пользователя страница 48

Страница: 48 / 48

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.

Catalog No. 04-53420022-01

Printed in U.S.A.

Form 42DHV-2SI

Pg CL-2

1-22

Replaces: 42DHV-1SI

Ductwork Connections

ARE DUCTWORK, FITTINGS AND GRILLES INSTALLED AS REQUIRED? (Y/N) __________

ARE FLEXIBLE DUCT CONNECTIONS AT UNIT?

(Y/N) __________

ARE THE PROPER SUPPLY AND RETURN GRILLE TYPE AND SIZE USED? (Y/N) __________

IS ALL DUCTWORK INSULATED, AS REQUIRED?

(Y/N) __________

IS OUTSIDE AIR CONTROLLED FOR FREEZE PROTECTION?

(Y/N) __________

Electrical Connections

REFER TO UNIT WIRING DIAGRAM TO ENSURE CONNECTIONS WERE MADE.

CONNECT INCOMING POWER SERVICE OR SERVICES.

__________

INSTALL AND CONNECT “FURNISH ONLY” PARTS.

__________

IS ALL FIELD WIRING IN CODE COMPLIANCE?

(Y/N) __________

Unit Start-up

PERFORM GENERAL VISUAL UNIT AND SYSTEM INSPECTION

__________

CHECK ALL WIRING FOR SECURE CONNECTIONS

__________

TIGHTEN ALL SET SCREWS

__________

CHECK CONDENSATE DRAIN CONNECTION

__________

VERIFY TRAP IS DEEP ENOUGH

__________

PRIME THE TRAP WITH WATER

__________

CHECK SUPPLY AND RETURN WATER CONNECTIONS FOR LEAKS

__________

FILL SYSTEMS WITH WATER/REFRIGERANT

__________

OPEN AIR VENT ON TOP OF COIL TO VENT AIR OUT OF SYSTEM

__________

FLUSH WATER SYSTEMS

__________

RECORD ELECTRICAL SUPPLY VOLTAGE

__________

CHECK FOR PROPER FAN ROTATION

__________

DUCTWORK AND GRILLES IN PLACE

__________

ALL UNIT PANELS AND FILTERS IN PLACE

__________

START FANS, PUMPS, CHILLERS, ETC.

__________

CHECK FOR OVERLOAD CONDITIONS OF ALL UNITS

__________

CHECK ALL DUCTWORK AND UNITS FOR AIR LEAKS

__________

BALANCE WATER SYSTEMS, AS REQUIRED

__________

BALANCE AIR SYSTEMS, AS REQUIRED

__________

RECORD ALL FINAL SETTINGS FOR FUTURE USE

__________

CHECK PIPING AND DUCTWORK FOR NOISE OR VIBRATION

__________

CHECK ALL DAMPERS FOR PROPER OPERATION

__________

VERIFY PROPER COOLING OPERATION

__________

VERIFY PROPER HEATING OPERATION

__________

REINSTALL ALL COVERS AND ACCESS PANELS

__________

VERIFY PROPER CONDENSATE DRAINAGE

__________

Recommended Maintenance
Quarterly

CHANGE AIR FILTERS

__________

Annually–In Addition to Quarterly Maintenance

INSPECT ALL WIRING CONNECTIONS AND TIGHTEN, IF NECESSARY

__________

CLEAN COIL AND DRAIN PAN

__________

CLEAN BLOWER WHEEL AS NEEDED

__________

Содержание 42DH

















































Результаты поиска

Содержание 42DH

Отзывы:

Похожие инструкции для 42DH

Бренды по названию

Популярные бренды

Carrier 42DH, Руководство пользователя

Результаты поиска

Содержание 42DH

Отзывы:

Похожие инструкции для 42DH

Бренды по названию

Популярные бренды