background image

40MUAA: Installation Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

2

MODEL NUMBERS AND 

ACCESSORIES

The Air Handler models are R-410A Fan Coils designed for 
installation flexibility allowing multi-position installation up-flow, 
down-flow, horizontal right and horizontal left. 

All fan coils have a DC fan motor with variable speeds for efficiency. 
The units have been designed for up-flow, down-flow, and horizontal 
orientations, including manufactured and mobile home applications.
A field supplied air filter and electrical disconnect are recommended.
These units are designed for specifically matching R-410A refrigerant
heat pumps. These units are available for 18,000 through 60,000
BTUh systems with nominal cooling capacity. 

ACCESSORIES

The system is shipped with the following accessories (see Table 2). Use 
all of the installation parts and accessories to install the system. Improper 
installation may result in water leakage, electrical shock and fire, or cause 
the equipment to fail. Keep the installation manual in a safe place and do 
not discard any accessories until the installation is complete.

Table 1 —Accessories 

EXPLOSION HAZARD

Failure to follow this warning could 

result in death, serious personal injury, 

and/or property damage.
Never use air or gases containing oxygen 
for leak testing or operating refrigerant 
compressors. Pressurized mixtures of air 
or gases containing oxygen can lead to 
an explosion.

WARNING

INSTALLATION

Entrust a licensed contractor to install the unit. Installation by 
unskilled persons may lead to improper installation, electric shock, 
or fire. Re-installation must be performed by authorized 
professionals. Non-compliance may lead to electric shock or fire.

WARNING

This unit is 

NOT

 equipped with a single point electrical 

connection for an Auxiliary Heat Package. A separate power 
supply is required for the Auxiliary Heat Package.

CAUTION

Name

Shape

Quantity

Owner’s and Installation 
Manual

2

Remote Controller

1

Batteries

2

Suction Line Flare to 
Braze Adapter

3/4” (18K-48K)
7/8” (60K)

1

Liquid Line Flare to Braze 
Adapter

3/8” (All Sizes)

1

Zip Ties

2

Coil Foam Tape

4

Flare Nut

2

Accessories included with the outdoor unit

Drain Adapter

1

Rubber Gasket

1

Suction Line Flare to Weld 
Adapter

3/4” (18K-48K)
7/8” (60K)

1

Liquid Line Flare to Weld 
Adapter

3/8” (All Sizes)

1

Suction Line reducer

1

Содержание 40MUAA

































Отзывы: