Carrier 39HXC Скачать руководство пользователя

Страница: 4 / 64

1 - PREAMBLE

This air handling unit is managed by its PLC. In addition to its control functions, it also monitors and detects any faults with the air

handling unit.
An HMI terminal associated with the PLC is used to view and modify the following parameters:

Values of connected sensors

Unit on/off cycles

Calibration of the sensors

Detection of alarms and log of the last 100 alarms

Password-protected configuration and operating parameters

Device running times and time delays

Managing time programs (6 weekly and 6 annual)

Language selection

Various terminal variants are available, to provide adaptability to the widest possible range of requirements:

Remote terminal

Terminal sharing between several air handling units

Simplified remote user control in the room to be conditioned

This device is not designed to be used by persons (including children) with limited physical, sensory or mental

capabilities, or by persons with insufficient experience or knowledge.

Only qualified personnel, who have received in-depth training in the equipment, are authorised to work on the machine or modify the

PLC's advanced parameters.
If it proves necessary to work on the unit, all the guidelines and instructions given in the maintenance brochures, on the labels or in

the instructions accompanying the equipment should first be observed, along with any other applicable safety advice. It is in particular

recommended to cut all the power supplies to the unit using the disconnect switch and/or circuit breakers, and wait for the motors and

all other moving mechanical parts to stop.

Содержание 39HXC

































































Результаты поиска

Содержание 39HXC

Отзывы:

Похожие инструкции для 39HXC

Бренды по названию

Популярные бренды

Carrier 39HXC, Руководство пользователя

Результаты поиска

Содержание 39HXC

Отзывы:

Похожие инструкции для 39HXC

Бренды по названию

Популярные бренды