manualshive.com logo in svg

Carrier 38UQZ016, Инструкции по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Carrier 38UQZ016 Скачать руководство пользователя страница 28

Table 11 - Troubleshooting chart

Symptoms 

Cause 

Remedy

Unit does not start 

No power supply 

Connect power supply

 

Main switch open 

Close switch

 

Low line voltage 

Check voltage and remedy the deficiency

 

A protection has tripped 

Reset

 

Contactor stuck open 

Replace contactor

 

Seized compressor 

Replace compressor

Unit starts and stops frequently 

Defective compressor contactor 

Replace contactor

 

Defective compressor 

Replace compressor

 

Refrigerant losses 

Check. Remove the charge. Repair leaks.

 

 

Evacuate. Recharge with refrigerant

Unit continuously cuts out at 

Defective low pressurestat 

Replace pressurestat

low pressure 

Refrigerant losses 

Check and add the necessary quantity

 

Indoor fan does not operate 

Check fan motor

Unit continuously cuts out at 

Defective high pressurestat 

Replace pressurestat

high pressure 

Refrigerant losses 

Check and correct

 

Outdoor fan does not operate 

Check fan motor

Abnormal system noise 

Piping vibration 

Support piping and check drainage

 

Noisy compressor 

Check and change if necessary

 

Badly fitting panels 

Install correctly

Water loss 

Defective drainage connections 

Check and tighten if necessary

Compressor loses oil 

Leak in system 

Repair leak

Order No. 13853-20, 12.07. Supersedes order No.: New 

Manufactured by: ECO, Guadalajara, Spain.

Manufacturer reserves the right to change any product specifications without notice. 

Printed in the Netherlands.

FINAL RECOMMENDATIONS

The unit you have purchased has undergone strict quality 
control procedures before leaving the factory.

All components, including the control systems and electrical 
equipment, etc., are certified by our Quality Control Depart-
ment, and tested under the harshest possible operating 
conditions in our laboratories. However, after leaving the 
factory, it is possible that one or more of these elements 
may be damaged due to causes beyond our control. In such 
an event, 

the user should not work on any of the internal 

components, or subject the unit to operating conditions 
which are not specified in this manual,

 since serious damage 

may result and the guarantee would be invalidated. Repair 
and maintenance work should always be left to the installer.

IMPORTANT: All recommendations concerning unit 
installation are intended to be as a guideline. Qualified 
technicians or installers must carry out the installation 
correctly and in accordance with applicable local, national 
and European standards and with the design conditions. 
They should also comply with all applicable regulations 
for air conditioning and refrigeration installations.

NOTE: The manufacturer does not accept responsibility 
for any malfunctions resulting from misuse of the 38UQZ 
and 40ALZ units, or from an incorrect installation and 
the damage caused by this.

Содержание 38UQZ016





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды